Toshiba e-studio 211c Operator'S Manual Download | Manualshive

Page: 167 / 225

background image

1

2

3

4

5

6

7

8

9

10

11

12

8-30

NETWORK SCANNING FUNCTION (USING THE OPTIONAL PRINTER CONTROLLER)

3. ABOUT THE SETTING BEFORE SCANNING (Cont.)

Setting the Administrator Password

The administrator sets the administrator password (5 digits). By this setting, the entry of the administrator
password becomes necessary for setting after pressing the ADMIN key. Only the administrator can
perform the setting with this key hereafter.
- The administrator password once set can be changed. In this case, the current administrator password

is needed.

- We recommend you to take a memo in order not to forget the administrator password.

Setting the New Administrator Password

1

Press the PRINTER/NETWORK key on the control

panel, then press the SCAN SETTING key on the

touch panel.

2

Press the PASSWORD SETTING key.

3

Key in the new password (the same number in 5 digits)

in both ‘NEW PASSWORD’ area and ‘VERIFY’ area, then

press the SET key.

- The setting of the new administrator password is completed.

If the screen is not switched by pressing the SET key in this
step, the number in ‘NEW PASSWORD’ area is different from
the one in ‘VERIFY’ area. In this case, press the letter entry
section in the ‘NEW PASSWORD’ area (or ‘VERIFY’ area) to
make the letter entry available again.

«
...
165
166
167
168
169
...
»

Summary of Contents for e-studio 211c


































































































































































































































Reviews:

No comments

Related manuals for e-studio 211c

imagePROGRAF iPF760

Brand: Canon Pages: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 16

imagePRESS C850

Brand: Canon Pages: 146

imagePRESS C850

Brand: Canon Pages: 63

imagePROGRAF iPF760

Brand: Canon Pages: 132

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 8

imagePROGRAF TX-2000

Brand: Canon Pages: 14

i-SENSYS MF6180dw

Brand: Canon Pages: 1040

imagePROGRAF iPF815

Brand: Canon Pages: 48

imageRUNNER 1025

Brand: Canon Pages: 6

imageRUNNER 2230

Brand: Canon Pages: 6

IMAGEPRESS C7010VPS

Brand: Canon Pages: 388

Brand: Canon Pages: 56

imagePROGRAF iPF8300

Brand: Canon Pages: 24

imagePROGRAF iPF8300

Brand: Canon Pages: 4

imagePROGRAF iPF6350

Brand: Canon Pages: 12

imagePROGRAF iPF6350

Brand: Canon Pages: 2

imageCLASS MF8380Cdw

Brand: Canon Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands