Toshiba e-STUDIO160 Service Handbook Download

Page: 181 / 239

December 2002 TOSHIBA TEC

4 - 59

e-STUDIO160/200/250 TROUBLESHOOTING

Measures

—

Clean rubber roller. Surface with alcohol

or replace it with new one.

Replace registration roller.

—

Replace process unit or drum.

Clean drum, replace process unit or drum.

Reinstall main drive gear assembly prop-

erly.

Replace drum drive gear.

Replace unit.

Criteria

Perform following procedures from 2 and

after.

—

Does the roller surface lack in friction and

is it slippery?

Uneven pitch approx. 94 mm overall?

Is there damage?

Is there any attached foreign matter?

Uneven pitch approx. 2.4 mm overall?

—

Uneven pitch approx. 0.3 mm overall?

Check item

Output built-in halftone

pattern on A3/LD.

(Code 109)

—

Check condition of

registration rubber roller

surface.

Check pattern.

Check drum surface.

Check pattern.

Summary of Contents for e-STUDIO160















































































































































































































































Search results

Summary of Contents for e-STUDIO160

Reviews:

Related manuals for e-STUDIO160

Brands by name

Popular brands

Toshiba e-STUDIO160, Service Handbook

Search results

Summary of Contents for e-STUDIO160

Reviews:

Related manuals for e-STUDIO160

Brands by name

Popular brands