Toshiba e-STUDIO160 Service Handbook Download

Page: 221 / 239

e-STUDIO160/200/250 UPDATING THE FIRMWARE

5 - 18

December 2002 TOSHIBA TEC

(10) Press any key on the PC.

Downloading of the main data begins.

Screen display on the PC

LCD display on the copier

Boxes ( ) are displayed one by one.

05-03-023

Important:

Some time after downloading begins, the message prompting you to perform the next

operation appears on the PC screen. However, downloading is in progress until the LCD of

the copier blinks as shown below. Do not perform any operation. Performing any operation

during this period may cause the downloading to be discontinued and fail and the PC may

not be recovered unless you use the recovery PWA.

Note:

The downloading time is about 1 minute and 30 seconds.

When downloading ends, all the dots on the copier LCD will blink.

Summary of Contents for e-STUDIO160















































































































































































































































Search results

Summary of Contents for e-STUDIO160

Reviews:

Related manuals for e-STUDIO160

Brands by name

Popular brands

Toshiba e-STUDIO160, Service Handbook

Search results

Summary of Contents for e-STUDIO160

Reviews:

Related manuals for e-STUDIO160

Brands by name

Popular brands