Toshiba E-Studio167 Service Manual Download

Page: 115 / 266

e-STUDIO167/207/237

SCANNER

6 - 23

[G] CIS unit (CIS)

(1)

Take off the original glass.

P.6-17 "[A] Original glass"

(2)

Move the CIS unit to the right most position.

Fig. 6-27

Notes:

•

Be sure to hold the CIS unit drive belt-1 to
move the CIS unit.

•

When the CIS unit is moved, be sure not
to touch the shaft as the silicon oil is
applied on it.

Fig. 6-28

(3)

Remove the seal which fixes the harness.

Note:

Attach the seal by following the procedure
below.

Place the flat harness along the edge
of the scanner base.

Align the seal with the two edges of
the scanner base.

Fig. 6-29

CIS unit

CIS unit drive belt-1

Seal

Harness

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands