Toshiba E-Studio167 Service Manual Download

Page: 183 / 266

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 13

[F]

Main charger cleaner

[G] Needle electrode

(1)

Take off the main charger.

P.11-12 "[D] Main charger"

(2)

Release the hook of the cleaning shaft. Then
rotate the shaft at 90 degrees to take it off.

Fig. 11-17

(1)

Take off the main charger grid and main
charger cleaner.

P.11-12 "[E] Main charger grid"

P.11-13 "[F] Main charger cleaner"

(2)

Take off the terminal covers of both front and
rear sides.

Fig. 11-18

(3)

Remove the terminal and spring. Then take
off the needle electrode.

Notes:

1. Do not touch the needle electrode directly

with bare hands.

2. Make sure not to hold or bend the needle

electrode.

Fig. 11-19

Main charger cleaner

Terminal cover

Needle electrode

Terminal

Spring

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands