Toshiba E-Studio167 Service Manual Download

Page: 185 / 266

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 15

[J]

Drum separation finger

[K] Recovery blade

(1)

Take off the drum.

P.11-14 "[H] Drum"

(2)

Take off 2 drum separation finger units by
removing 1 screw each.

Note:

When replacing the drum separation fingers,
make sure that the drum has been taken off
first since the fingers may scratch the drum
surface.

Fig. 11-22

(3)

Take off the drum separation finger with the
spring.

Note:

When the drum separation fingers have been
replaced, check if the pressure movement is
normal by moving them with your hands.

Fig. 11-23

(1)

Take off 2 drum separation finger units.

P.11-15 "[J] Drum separation finger"

(2)

Remove 2 screws, and take off the whole
recovery blade with the bracket.

Fig. 11-24

Drum separation finger unit

Drum separation finger

Spring

Recovery blade

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands