Toshiba E-Studio167 Service Manual Download

Page: 191 / 266

e-STUDIO167/207/237

DRUM RELATED SECTION

11 - 21

[Q] Temperature/humidity sensor (S3)

[R] Toner cartridge interface PC board (CTIF)

(1)

Take off the left cover.

P.2-19 "[C] Left cover"

(2)

Disconnect 1 connector, remove 1 screw,
and then take off the temperature/humidity
sensor.

Fig. 11-40

(1)

Take off the process unit.

P.11-17 "[N] Transfer unit"

(2)

Take off the inner tray.

P.2-18 "[B] Inner tray"

(3)

Disconnect 1 connector, remove 1 screw and
then take off the toner cartridge interface PC
board.

Fig. 11-41

Temperature/
Humidity sensor

Connector

Toner cartridge
interface PC board

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands