Toshiba E-Studio167 Service Manual Download

Page: 202 / 266

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 10

2) Function of auto-toner sensor

The auto-toner sensor consists of the following circuits:

Drive winding:
A magnetic head (primary side) with a high-frequency magnetic field, which forms a magnetic cir-
cuit in the developer material.

Detection winding:
Receives the change in the magnetic resistance of the developer material through the magnetic
circuit (secondary side).

DC conversion circuit:
Converts a high-frequency output from the detection winding into a DC signal (auto-toner output
V

ATS

Fig. 12-5

When the toner density is low

The ratio of the toner against the carrier in the developer material decreases.

The magnetic resistance decreases.

The detection output increases.

The auto-toner output V

ATS

increases.

When the toner density is high

The ratio of the toner against the carrier in the developer material increases.

The magnetic resistance increases.

The detection output decreases.

The auto-toner output V

ATS

decreases.

Drive

winding

Detection

winding

conversion

circuit

Auto-toner sensor

output

To the A/D converter

(MAIN board)

ATS-1A

Magnetic circuit

Magnetic resistance

Developer material

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands