Toshiba E-Studio167 Service Manual Download

Page: 203 / 266

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 11

12.6 Disassembly and Replacement

[A] Developer unit

Note:

Make sure to perform “05-280” and take off the process unit before the developer material is
replaced.

(1)

Take off the Process unit.

P.11-9 "[A] Process unit"

(2)

Take off the drum cleaner unit from the pro-
cess unit so that only the developer unit will
be left.

P.11-10 "[B] Drum cleaner unit"

Notes:

1. Be careful not to touch or scratch the

drum surface at this time.

2. Do not deform the Guide Mylar by touch-

ing this.

Fig. 12-6

Fig. 12-7

Developer unit

Drum cleaner unit

Guide mylar

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands