Toshiba E-Studio167 Service Manual Download

Page: 206 / 266

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 14

[E]

Drum thermistor (THMS4)

[F]

Guide roller / Developer sleeve

(1)

Remove the developer material.

P.12-12 "[B] Developer material"

(2)

Disconnect 1 connector, remove 1 screw and
take off the drum thermistor.

Fig. 12-13

(1)

Remove the developer material.

P.12-12 "[B] Developer material"

(2)

Remove 2 screws and take off the recovered
toner supply unit.

Fig. 12-14

(3)

Remove 1 screw. Disconnect 1 connector
while taking off the recovered toner drive
unit. Remove 1 gear.

Fig. 12-15

Drum thermistor

Connector

Recovered toner
supply unit

Gear

Recovered toner drive unit

Connector

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands