Toshiba E-Studio167 Service Manual Download

Page: 213 / 266

e-STUDIO167/207/237

DEVELOPMENT SYSTEM

12 - 21

[H] Replacement of Oil Seal

(11) Remove the bushing on the rear side.
(12) Remove the oil seal.

(Replacement of Oil seal:

P.12-21 "[H]

Replacement of Oil Seal")

Fig. 12-34

(1)

Insert a fine screwdriver into the depression
of the oil seal to take it out.

(2)

Push in a new oil seal parallel to the frame or
bushing (shown figure at right).

(3)

Apply the grease (Alvania No.2; amount of 2
rice grains) on entire surface of the oil seal
evenly.

Note:

Wipe off the excessive grease.

Fig. 12-35

Oil seal

Bushing

Outside

Inside

Oil seal

Grease

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands