Toshiba E-Studio167 Service Manual Download

Page: 226 / 266

e-STUDIO167/207/237

FUSER / EXIT UNIT

13 - 12

13.6 Disassembly and Replacement

[A] Fuser / Exit unit

[B] Pressure roller unit / Fuser roller unit

(1)

Take off the right rear cover.

P.2-22 "[I] Right rear cover"

(2)

Lay down the transfer unit.

(3)

Disconnect 3 connectors, remove 2 screws,
and then take off the fuser/paper exit unit.

Note:

Be careful because the fuser/paper exit unit
is hot.

Fig. 13-6

(1)

Take off the fuser/paper exit unit.

P.13-12 "[A] Fuser / Exit unit"

(2)

Remove 1 spring and 2 screws.

(3)

Separate the pressure roller unit from the
fuser roller unit.

Note:

If the ADU (optional) is installed, the spring
has already been removed.

Fig. 13-7

Note:

Separate the pressure roller and the heat
roller while pressing the thermistor ground
leaf spring.

Fig. 13-8

Connector

Screw

Fuser/ Paper exit unit

Stepped screw

Pressure roller unit

Fuser roller unit

Spring

Thermistor ground leaf spring

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands