Toshiba E-Studio167 Service Manual Download

Page: 233 / 266

e-STUDIO167/207/237

FUSER / EXIT UNIT

13 - 19

[H] Pressure roller

(4)

Remove 1 C-ring and 1 bushing on the front
side of the fuser roller.

(5)

Remove 1 C-ring, 1 gear and 1 bushing on
the rear side of the fuser roller.

Fig. 13-26

(1)

Take off the pressure roller unit.

P.13-12 "[B] Pressure roller unit / Fuser

roller unit"

(2)

Remove 3 screws, and then take off the
fuser unit entrance guide.

Fig. 13-27

(3)

Remove 2 springs.

Note:

When installing the spring, be sure to hang
the spring on the upper hook.

Fig. 13-28

Bushing

Gear

C-ring

Fuser unit entrance guide

Spring

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands