Toshiba E-Studio167 Service Manual Download

Page: 30 / 266

e-STUDIO167/207/237

OUTLINE OF THE MACHINE

2 - 14

7) Thermistors and thermostats

8) Others

Symbol

Name

Function

Remarks

P-I

THMS1

THMS-C-HTR
Center thermistor

Detecting the surface temperature at
the center of the fuser roller (for con-
trolling the center heater lamp)

Fig. 2-5

23-6

THMS2

THMS-S-HTR
Side thermistor

Detecting the surface temperature at
the rear side of the fuser roller (for con-
trolling the side heater lamp)

Fig. 2-5

23-6

THMS3

THMS-EDG-HTR
Edge thermistor

Detecting the surface temperature at
the edge of the rear side of the fuser
roller (for preventing overheating)

Fig. 2-5

23-6

THMS4

THMS-DRM
Drum thermistor

Detecting the temperature on the drum
surface

Fig. 2-6

21-49

THMO1

THERMO-FSR
Fuser thermostat

Preventing overheating in the fuser unit

Fig. 2-5

23-5

THMO2

THERMO-SCN-DH
Scanner damp heater thermostat

Preventing overheating in the scanner
damp heater
*

Optional for NAD/MJD/CND model,
standard for other models

Fig. 2-3

9-20

THMO3

THERMO-DRM-DH
Drum damp heater thermostat

Preventing overheating in the drum
damp heater
*

Optional for NAD/MJD/CND model,
standard for other models

Fig. 2-6

8-7

Symbol

Name

Function

Remarks

P-I

CIS

CIS
Contact image sensor unit

Reading originals

Fig. 2-3

9-8

PS-ACC
Switching regulator

•

Generating DC voltage and supply-
ing it to each section of the equip-
ment

•

Generating high voltage and sup-
plying it to the main charger, devel-
oper, transfer and separation units

•

Supplying AC power to the heater
lamp

Fig. 2-4

5-2

LCD

LCD
LCD panel

Displaying each information

Fig. 2-3

4-19

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands