Toshiba E-Studio167 Service Manual Download

Page: 72 / 266

e-STUDIO167/207/237

GENERAL OPERATION

4 - 4

4.2.4

Bypass feed copying

1) Insert a sheet of paper into the bypass tray.

Bypass paper sensor ON

Bypass feed priority state.

2) Press the [START] button

“READY” Æ “COPYING”

CIS LED ON

Scan motor ON

CIS unit move forward

Polygonal motor rotates in high speed

Main motor and exit motor ON

The drum, fuser unit, developer unit and exit roller are driven.

3) Bypass feeding

Main charger, developer bias and discharge LED ON. Fans are rotated in high speed.

Bypass pickup solenoid ON

The bypass pickup roller start to rotate.

The bypass pickup roller is lowered.

The bypass feed roller start to rotate.

Paper reaches the registration roller

Aligning operation

After a certain period of time, the bypass pickup solenoid OFF

4) Hereafter, the operation 3) through 6) of

P.4-3 "4.2.3 Drawer feed copying" is repeated.

4.2.5

Interruption copying

1) Press the [INTERRUPT] button

LED “INTERRUPT” ON

Copying operation in progress is temporarily stopped. CIS unit return to appropriate positions

“Job interrupted” is displayed

Automatic density and reproduction ratio 100% are set (The set number remains the same)

2) Select the desired copy condition

3) After the interruption copying is finished:

LED “INTERRUPT” OFF by pressing the [INTERRUPT] button

“READY to resume job” is displayed

4) Press the [START] button

The copying operation before the interruption is resumed

Summary of Contents for E-Studio167
























































































































































































































































Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands

Toshiba E-Studio167, Service Manual

Search results

Summary of Contents for E-Studio167

Reviews:

Related manuals for E-Studio167

Brands by name

Popular brands