Toshiba e-studio550 Service Handbook Download

Page: 127 / 313

JUNE 2002 © TOSHIBA TEC

4 - 23

e-STUDIO550/650/810 PREVENTIVE MAINTENANCE

4. 7. 4. Handling of drum cleaning brush and transfer belt cleaning brush

Do not touch the brush surface with bare hands.

4. 7. 5. Handling of transfer belt

(1) Do not touch the belt surface with your bare hands.

(2) Prevent oil or other foreign matter from adhering to the belt surface.

(3) Do not touch the transfer belt with alcohol or other organic solvents.

(4) Do not apply external pressure that might scratch the transfer belt.

4. 7. 6. Checking and cleaning of fuser roller and pressure roller

(1) Handling precautions

• Do not leave oil (fingerprints, etc.) on the fuser roller.

• Be extremely careful not to allow a hard object to hit or rub against the rollers because the thin

teflon layer coated on the aluminum substrate is easily damaged and, if damaged, will result in

defective drum cleaning.

(2) Checking

• Check for stain and damage to the fuser and pressure rollers and clean or replace if necessary.

• Clean the upper/lower separation fingers and check for chipped claws.

• Check the cleaning condition of the cleaning WEB and cleaning roller (kinks, lines and slacks

on the cleaning WEB).

• Check the thermistor for proper contact with the fuser roller.

• Check the fused condition of the toner image.

• Check the gap between the lower entrance guide and pressure roller (do not make them touch

each other).

• Check the gap between the fuser roller and thermostat (2~2.5mm).

• Check the fuser and pressure rollers for proper rotation.

• Check the fuser and pressure rollers for bearing.

• Check the fuser roller drive gear and cleaning WEB drive gear

• Check the WEB motor lubrication to the warm gear (white molycote).

(3) Cleaning procedure for fuser roller

When the fuser roller becomes dirty, it will cause paper jamming. If this happens, wipe the roller surface

clean with cotton moistened in alcohol. For a better cleaning effect, clean the roller when it is still warm.

Note: Be careful not to rub the teflon-coated surface with your fingernails or hard objects because it is easily

damaged. Do not apply the silicon oil to the fuser roller.

(2) Cleaning procedure

Clean the blade edge with a cloth moistened with water and squeezed lightly.

Summary of Contents for e-studio550


























































































































































































































































































































Search results

Summary of Contents for e-studio550

Reviews:

Related manuals for e-studio550

Brands by name

Popular brands

Toshiba e-studio550, Service Handbook

Search results

Summary of Contents for e-studio550

Reviews:

Related manuals for e-studio550

Brands by name

Popular brands