Toshiba e-studio550 Service Handbook Download

Page: 133 / 313

JUNE 2002 © TOSHIBA TEC

5 - 5

e-STUDIO550/650/810 TROUBLE SHOOTING

[E25] External LCF transport jam (paper not reaching the registration sensor)

Is there any paper before the registration sensor when the bypass unit cover is opened?

Remove the paper.

Is the registration sensor working? (Perform the input check in the test mode: 03-[ENERGY

SAVER]ON/[4]/[E])

1. Check if the registration connector is not disconnected.

2. Check if the connector J341 on the LGC board is not disconnected.

3. Check if the connector pins are not disconnected and the harness is not

open-circuited.

4. Check if the conductor pattern on the LGC board is not short- or open-

circuited.

5. Replace the registration sensor.

6. Replace the LGC board.

Is the external LCF transport motor driving? (Perform the output check in the test mode: 03-122/172)

1. Check if the connector of the transport motor is not disconnected.

2. Check if the connectors J801~804 on the LCF board are not disconnected.

3. Check if there is any abnormality at the transort drive unit.

Is the external LCF feed clutch working? (Perform the output check in the test mode: 03-272)

1. Check if the external LCF clutch connector is not disconnected.

2. Check if the connectors J801~804 on the LCF board are not disconnected.

3. Check if the connector J346 on the LGC board is not disconnected.

4. Check if the connector pins are not disconnected and the harness is

not open-circuited.

5. Check if the conductor pattern on the LCF and LGC boards is not

short- or open-circuited.

6. Replace the external LCF feed clutch.

7. Replace the LCF board.

8. Replace the LGC board.

YES

Summary of Contents for e-studio550


























































































































































































































































































































Search results

Summary of Contents for e-studio550

Reviews:

Related manuals for e-studio550

Brands by name

Popular brands

Toshiba e-studio550, Service Handbook

Search results

Summary of Contents for e-studio550

Reviews:

Related manuals for e-studio550

Brands by name

Popular brands