241
6
F
2
S
0
7
8
9
Modbus: Interoperability
1. Physical and Data Link Layer
- RS485(EIA/TIA-485) 2-wire interface
- RTU mode only
- Coding System:
8
–
bit binary (1 start bit, 8 data bits, 1 parity bit, 1 stop bit)
Even parity
- Address setting range: 1-247
- Baud rate setting range: 9600 or 19200
2. Application Layer
(1) Modbus response format
FC Description
Supplementary explanation
01 Read Coils
Returns remote control enable flag
02 Read Discrete Inputs
Returns BIs or LED lamp status, etc.
03 Read Holding Registers
-
04 Read Input Register
Returns value of analog inputs
05 Write Single Coil
Remote command and Time synchronization
06 Write Single Register
Need to specify record number
07 Read Exception status
Returns relay and CB status
08 Diagnostic
-
16 Write Multiple Registers
Current time setting, etc.
17 Report Slave ID
Returns device ID
43 Read device Identification (SC:14)
Returns device information
For FC=01, 02, 03, 04, 05, 06 and 16, the response format is the same as described in "MODBUS
Application Protocol Specification V1.1b".
For other FCs, the response format is as following:
07 Read Exception status
Response Data
Output Data (1byte)
bit Description
0 IN SERVICE (LED)
1 TRIP (LED)
2 ALARM (LED)
3 Testing (LED)
4 Prog. LED1 (LED)
5 Prog. LED2 (LED)
6 Prog. LED3 (LED)
7 Relay fail output (BO)
Summary of Contents for GRT100 Series
