Toshiba MBSWH-10K-F3-KK, Installation Manual

MBS (Wallmount) Installation - 64523-009

3

WARNING AREA

TEXT AREA

DANGER

Hazardous voltages are used in the operation
of this equipment and could cause severe personal
injury or loss of life.
The following precautions should be observed to
reduce the risk of injury or death.

HAZARDOUS VOLTAGES

Only qualified technicians familiar with this equipment and the
information supplied with it should be permitted to install and
operate this equipment.
Installation of electrical equipment must be done in
accordance with National Electrical Code and any other state
or local codes. Proper grounding and conductor sizing must
be installed for safe operation.

During operation, keep all covers in place and cabinet
doors shut.

When performing visual inspections and maintenance, if
possible, be sure the MBS is turned off and the incoming
AC feed is turned off and locked out.

If it is necessary to make measurements with the power
on, do not touch any electrical connection points. Remove
all jewelry from wrists and fingers. Make sure test equipment
is in good, safe operating condition.

While servicing, stand on some type of insulation, and be
sure not to be grounded.

Follow the safety instructions given in the equipment manual
carefully and observe all danger, warning and caution notices.

64818

MATERIAL - VINYL OR POLYESTER
TEMPERATURE - MINUS 20 TO 100 deg. C
ADHESIVE - V23 OR EQUIV.
MUST RESIST OIL SOLVENTS
ALL MATERIALS USED MUST
BE UL RECOGNIZED

WARNING AREA BACKGROUND COLOR: ANSI DANGER RED
WARNING AREA TEXT COLOR: ANSI WHITE
TEXT AREA BACKGROUND COLOR: ANSI WHITE
TEXT AREA TEXT COLOR: ANSI BLACK
CORNER RADIUS: VENDOR STANDARD

0.00

0.00

3.75

4.50

The UPS and Battery Cabinet will have hazardous
voltages present even after the AC feed is turned off.

THIS MATERIAL IS THE EXCLUSIVE PROPERTY OF TOSHIBA INTERNATIONAL
CORPORATION AND SHALL NOT BE REPRODUCED, USED, OR DISCLOSED
TO OTHERS UNLESS PRIOR WRITTEN AUTHORIZATION IS OBTAINED.

TITLE:

SCALE:

DRAWING NO.:

ECN

DATE

BY

DRAWN:

CHECKED:

APPROVED:

DANGER LABEL
GENERAL - MBS

64818

FULL

WLM 3-9-11

REV:

0

13131 WEST LITTLE YORK ROAD, HOUSTON, TX 77041 U.S.A.

WLM 3-10-11

ZIR 3-10-11

UNLESS

PRIOR

WRITTEN

AUTHORIZA

TION

IS
OBT

AINED.

THIS

MA

TERIAL

IS
THE

EXCLUSIVE

PROPER

TY

OF

BE

REPRODUCED,

U

SED

OR

DISCLOSED

T

O
OTHERS

T

O

SHIBA

INTERNA

TIONAL

CORPORA

TION

AND

SHALL

NOT

APPROVED

BY

DA
TE

CHECKED

BY

DRA

WN

BY

DA
TE

DA
TE

DRA

WING

NO.

13131

WEST

LITTLE

YORK

ROAD,

HOUST

ON,

TX,

77041

U.S.A.

TITLE

SCALE

OF

SH.

ORDER

NO.

64820

W

ALL

MOUNT

MBS

CONNECTION

LABEL

SHEET

1=1

11

DISK:

PR
T

REV

:

1

A

B

C

1/2” BOLT-SAE GRADE 8

TORQUE SPEC: 119 FT LB

ENSURE PROPER PHASING

LINE IN

USE COPPER CONDUCTORS ONLY!

REFER TO INSTRUCTION MANUAL FOR WIRE SIZE

A

B

C

1/2” BOLT-SAE GRADE 8

TORQUE SPEC: 119 FT LB

ENSURE PROPER PHASING

LOAD IN

USE COPPER CONDUCTORS ONLY!

REFER TO INSTRUCTION MANUAL FOR WIRE SIZE

A

B

C

1/2” BOLT-SAE GRADE 8

TORQUE SPEC: 119 FT LB

ENSURE PROPER PHASING

UPS IN

USE COPPER CONDUCTORS ONLY!

REFER TO INSTRUCTION MANUAL FOR WIRE SIZE

A

B

C

1/2” BOLT-SAE GRADE 8

TORQUE SPEC: 119 FT LB

ENSURE PROPER PHASING

UPS OUT

USE COPPER CONDUCTORS ONLY!

REFER TO INSTRUCTION MANUAL FOR WIRE SIZE

B1

CB2

NEUTRAL

SKRU

B1

1

2

T

C

4.50"

3.50"

1.75"

MA

TERIAL

-

POL

YESTER

TEMPERA

TURE

-

MINUS

20
T

O
100

deg.

C

ADHESIVE

-

V23

OR

EQUIV

.

MUST

RESIST

OIL

SOL

VENTS

ALL

MA

TERIALS

USED

MUST

BE

UL

&
RoHS

RECOGNIZED

TEXT

BACKGROUND:

ANSI

WHITE

OR

SIL

VER

TEXT

COLOR:

ANSI

BLACK

KISS

CUT

T

O
BORDER

LINES

6.00"

9.00"

1.75"

CB3

GND

INITIAL

RELEASE

04-1

1

ZIR

1.00"

1.50"

1.00"

WLM

4-24-13

3/8” BOLT-SAE GRADE 8

TORQUE SPEC: 47 FT LB

3/8” BOLT-SAE GRADE 8

TORQUE SPEC: 47 FT LB

3/8” BOLT-SAE GRADE 8

TORQUE SPEC: 47 FT LB

3/8” BOLT-SAE GRADE 8

TORQUE SPEC: 47 FT LB

ECO

86630

04-13

WLM

WLM

3-9-1

1

ZIR

4-24-13

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation, maintenance, and operation of 

the MBS to assure safe and proper operation. 

1. 

Turn off, lockout, and tagout all power sources before connecting the power and SKRU wiring to the equipment or 

when performing maintenance.

2.  Verify the MBS is de-energized before removing the cabinet dead fronts.

3.  Verify cables and terminals are de-energized before installing cable in terminals. 

Qualified Personnel ONLY!

Qualified Personnel is one that has the skills and knowledge relating to the construction, installation, operation, and main

-

tenance of the electrical equipment and has received safety training on the hazards involved (Refer to the latest edition of 

NFPA 70E for additional safety requirements).

Qualified Personnel shall:

1.  Have read the entire operation manual.

2.  Be trained and authorized to safely energize, de-energize, ground, lockout and tag circuits and equipment, and 

clear faults in accordance with established safety practices.

3.  Be trained in the proper care and use of protective equipment such as safety shoes, rubber gloves, hard hats, 

safety glasses, face shields, flash clothing, etc., in accordance with established safety practices.

4. 

Be trained in rendering first aid.

5.  Be knowledgeable of batteries and the required handling and maintenance precautions.

For further information on workplace safety visit 

www.osha.gov

.