background image

MBS (Wallmount) Installation - 64523-009

4

SHIPPING DIMENSIONS

The shipping dimensions for the wall-mount MBS are given in the table below.

Table 1:  Shipping Dimensions

ITEM

Shipping Dim. (LxWxH)

Medium MBS Case 

36” x 47” x 14”

Large MBS Case

41” x 53” x 19”

MOUNTING INSTRUCTIONS

The Toshiba wall-mounted Maintenance Bypass cabinet  comes fully assembled.  The units are equipped with two lifting 

eyes each on the top and bottom of the cabinet.  Inside on the back panel are four keyholes sized for 1/2” mounting bolts 

(customer supplied) that are for mounting the unit to cement wall or metal channel support.

    See the appropriate draw-

ing for the support dimensions and spacing.

Removable 14 gage steel access plates are provided at the top and bottom for anchoring power cable conduit.  

LOCK-OUT/TAG-OUT (LOTO) HASP

A pair of interleaving tabs are included to provide a LOTO hasp to satisfy applications that require 

Lock-out/Tag-out capability.  Instructions for installing this hasp are given in Appendix A.

POWER CABLING INSTRUCTIONS

The MBS Circuit Breakers are equipped with terminal bus strips. The terminal bus strips are pre-drilled with standard 

2-hole NEMA patterns to facilitate installation of power cables:  

 

Medium Case - 3/8 in. bolt holes on 1.75 in. centers

 

Large Case - 1/2 in. bolt holes on 1.75 in. centers  

Use of NEMA two-hole cable terminations is recommended.

NOTE: Cables, Cable Lugs (Fittings), and fastening bolts/hardware are to be provided by others.

Table 2:  Recommended Bolt Tightening Specifications

ITEM

Fasteners

Torque 

Medium MBS Case

Grade 8, 3/8 in. Bolts

47 ft-lb (5.3 N•M)

Large MBS Case

Grade 8, 1/2 in. Bolts

119 ft-lb (13.4 N•M)

 The following table lists examples of recommended 2 hole compression type fittings. 

Table 3:  Compression Fittings: 2 hole, 3/8 in. x 1.75”

Ilsco P/N

Description

Hole  

Diameter

Hole  

Spacing

Conductor 

Size

Fitting Color

CLND-6-38-134

Long Barrel

3/8 in.

1.75 in.

#6

Blue

CLND-2-38-134

CSWD -2-38-134

Long Barrel

Short Barrel

3/8 in.

1.75 in.

#2

Brown

CLND-1/0-38-134

CSWD -1/0-38-134

Long Barrel

Short Barrel

3/8 in.

1.75 in.

1/0

Pink

CLND-2/0-38-134

Long Barrel

3/8 in.

1.75 in.

2/0

Black

Summary of Contents for MBSWH-10K-F3-KK














Reviews: