Installation Manual
– 24 –
EN
EN-47
EN-48
(Execute it while the units are stopped.)
The indoor unit numbers in a group are indicated one after another. The fan and louvers of the indicated units are
activated.
1
Push and hold the
and
buttons at the same time for more than 4 seconds.
•
appears on UNIT No. on the LCD display.
• The fans and louvers of all the indoor units in the group are activated.
2
Push the
button (left side of the button). Each time you push the button, the indoor unit numbers
are indicated one after another.
• The first-indicated unit number is the address of the header unit.
• Only the fan and louvers of the indicated indoor unit are activated.
3
Push the
button to finish the procedure.
All the indoor units in the group stop.
To check all the indoor unit addresses using an arbitrary wired remote controller.
(When communication wirings of 2 or more refrigerant lines are interconnected for central control)
(Execute it while the units are stopped.)
You can check indoor unit addresses and positions of the indoor units in a single refrigerant line.
When an outdoor unit is selected, the indoor unit numbers of the refrigerant line of the selected unit are indicated one
after another and the fan and louvers of the indicated indoor units are activated.
1
Push and hold the TIME
and
buttons at the same time for more than 4 seconds.
At first, the line 1 and CODE No.
(Address Change) are indicated on the LCD display. (Select an
outdoor unit.)
2
Push the
(left side of the button) and
buttons repeatedly to select a system address.
3
Push the
button to confirm the system address selection.
• The address of an indoor unit connected to the selected refrigerant line is indicated on the LCD display and its
fan and louvers are activated.
4
Push the
button (left side of the button). Each time you push the button, the indoor unit numbers
of the selected refrigerant line are indicated one after another.
• Only the fan and louvers of the indicated indoor unit are activated.
UNIT LOUVER
5
6
1
3
4
2
ON / OFF
TEMP.
TIME
SET CL
FILTER
RESET TEST
TIMER SET
CODE No.
UNIT No.
SETTING
DATA
SET
R.C.
No.
UNIT LOUVER
SWING/FIX
UNIT LOUVER
To select another system address
5
Push the button to return to step 2.
• After returning to step 2, select another system address and check the indoor unit addresses of the line.
6
Push the
button to finish the procedure.
Changing the indoor unit address using a remote controller
To change an indoor unit address using a wired remote controller
The method to change the address of an individual indoor unit (the indoor unit is paired with a wired remote
controller one-to-one), or an indoor unit in a group.
(The method is available when the addresses have already been set automatically.)
(Execute it while the units are stopped.)
1
Push and hold the
, , and
buttons at the same time for more than 4 seconds.
(If 2 or more indoor units are controlled in a group, the first indicated UNIT No. is that of the head unit.)
2
Push the
button (left side of the button) repeatedly to select an indoor unit number to change if 2
or more units are controlled in a group. (The fan and louvers of the selected indoor unit are activated.)
(The fan of the selected indoor unit is turned on.)
3
Push the TEMP.
/
buttons repeatedly to select
for CODE No.
4
Push the TIME
/
buttons repeatedly to change the value indicated in the SET DATA section to that
you want.
5
Push the
button.
6
Push the
button (left side of the button) repeatedly to select another indoor UNIT No. to change.
Repeat steps
4
to
6
to change the indoor unit addresses so as to make each of them unique.
7
Push the
button (left side of the button) to check the changed addresses.
8
If the addresses have been changed correctly, push the
button to finish the procedure.
3
5
8
1
4
2, 6, 7
ON / OFF
TEMP.
TIME
SET CL
FILTER
RESET TEST
TIMER SET
CODE No.
UNIT No.
SETTING
DATA
SET
R.C.
No.
Finish
UNIT LOUVER
UNIT LOUVER
UNIT LOUVER
2FAN_IM_DB04905901-00.book Page 24 Friday, October 24, 2014 3:19 PM
Summary of Contents for MCY-MAP0401TP Series
Page 32: ......
