background image

42-EN

41-EN

– 21 –

<In the case of combining with outdoor units of Super Modular Multi System u series (SMMS-u)>

Uv

 line and 

Uc

 line (

L2, L3, L4

)

(2-core shield wire, non-polarity)

Wire size : 

1.0 to 1.5 mm²

(Up to 1000 m)

Uh

 line (

L1

)

(2-core shield wire, non-polarity)

Wire size :

1.0 to 1.5 mm²
2.0 mm²

(Up to 1000 m)
(Up to 2000 m)

 

y

U (v, h, c)

 line means of control wiring.

Uv

 line : Between indoor and outdoor units.

Uh

 line : Central control line.

Uc

 line : Between outdoor and outdoor units.

 

y

Uv

 line and 

Uc

 line are independent from another refrigerant line. Total length of 

Uv

 and 

Uc

 lines 

(L3+L4)

 in 

each refrigerant line is up to 1000 m.

REQUIREMENT

For connection of Uv line / Uc line or Uh line, wire each line using wires with the same type and size. 
If different wire types and size are mixed and used in a system, communication trouble is caused.

[Uh line]
 L1 

= Up to 2000 m

[Uv and Uc line]
 L2 

= Up to 1000 m

 

(L3+L4)

 = Up to 1000 m

Central control device

Outdoor unit

Indoor unit

Remote controller

<U series>

<U series>*

<U series>*

(SMMS-u)

* Even if the indoor unit and the remote controller are "other than U series", the wiring 

speci

fi

 cation are the same.

 

„

Power supply wire and communication wires speci

fi

cations

Power supply wire and communication wires are locally procured.
For the power supply speci

fi

cations, follow to the table below. If capacity is little, it is dangerous because overheat 

or burnout may be caused.
For speci

fi

cations of the power capacity of the outdoor unit and the power supply wires, refer to the Installation 

Manual attached to the outdoor unit.

Indoor unit power supply

 

y

For the power supply of the indoor unit, prepare the exclusive power supply separated from that of the outdoor 
unit.

 

y

Arrange the power supply, circuit breaker, and main switch of the indoor unit connected to the same outdoor unit 
so that they are commonly used.

 

y

Power supply wire speci

fi

cation: Cable 3-core 2.5 mm², 

in conformity with Design 60245 IEC 57

.

 

„

Power supply

Power supply

220V-240V ~, 50Hz
208V-230V ~, 60Hz

Power supply switch / circuit breaker or power supply wiring / fuse rating for indoor units should be selected by the 
accumulated total current values of the indoor units.

Power supply wiring

Below 50 m

3 × 2.5 mm² (power supply and earth)

Control wiring, Central controller wiring

 

y

2-core with polarity wires are used for the Control wiring between indoor unit and outdoor unit and Central 
controller wiring.

 

y

To prevent noise trouble, use 2-core shield wire.

 

„

Communication line

TU2C-Link models (U series) can be combined with TCC-Link models (other than U series).
For details of communication type, refer to the following table.

Communication type and model names

Communication 

type

TU2C-Link

(U series and future models)

TCC-Link

(Other than U series)

Outdoor unit

MMY-MUP

ÛÛÛ

 
 

This letter indicates U series model.

Other than U series
MMY-MHP

ÛÛÛ

 , MMY-MAP

ÛÛÛ

MCY-MHP

ÛÛÛ

Indoor unit

MM

Û

-UP

ÛÛÛ

 
 

This letter indicates U series model.

Other than U series
MM

Û

-AP

ÛÛÛ

Wired remote 
controller

RBC-ASCU

ÛÛÛ

 
 

This letter indicates U series model.

Other than U series

Wireless remote 
controller kit & 
receiver unit

RBC-AXU

ÛÛÛ

 
 

This letter indicates U series model.

Other than U series

U series outdoor unit : SMMS-u (MMY-MUP

ÛÛÛ

)

Other than U series outdoor unit : SMMS-i, SMMS-e etc. (MMY-MHP

ÛÛÛ

 , MMY-MAP

ÛÛÛ

)

Summary of Contents for MMD-UP0721HFP-E






































Reviews: