background image

– 2 –

EN

„

Warning indications on the air conditioner unit

Warning indication

Description

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote electric power supplies before servicing.

WARNING

Moving parts. 
Do not operate unit with grille removed. 
Stop the unit before the servicing.

CAUTION

High temperature parts. 
You might get burned when removing this panel.

CAUTION

Do not touch the aluminum fins of the unit. 
Doing so may result in injury.

CAUTION

BURST HAZARD

Open the service valves before the operation, otherwise there might be the 
burst.

CAUTION

Do not climb onto the fan guard.

Doing so may result in injury.

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote 
electric power supplies 
before servicing.

WARNING

Moving parts.
Do not operate unit with grille 
removed.
Stop the unit before the servicing.

CAUTION

High temperature parts.
You might get burned 
when removing this panel.

CAUTION

Do not touch the aluminum 
fins of the unit.
Doing so may result in injury.

CAUTION

BURST HAZARD

Open the service valves before 
the operation, otherwise there 
might be the burst.

CAUTION

Do not climb onto the 
fan guard. 

Doing so may result in injury. 

1

Precautions for safety

The manufacturer shall not assume any liability for the damage caused by not observing the description of this 
manual.

WARNING

General

• Carefully read Owner’s Manual before starting the air conditioner. There are many important things to keep in mind for daily 

operation.

• Ask for installation to be performed by the dealer or a professional. Only a qualified installer (*1) is able to install an air 

conditioner. If a non-qualified person installs an air conditioner, it may result in problems such as fire, electric shock, injury, 
water leakage, noise and vibration. 

• Do not use any refrigerant different from the one specified for complement or replacement.

Otherwise, abnormally high pressure may be generated in the refrigeration cycle, which may result in a failure or explosion 
of the product or an injury to your body.

• Places where the operation sound of the outdoor unit may cause a disturbance. (Especially at the boundary line with a 

neighbor, install the air conditioner while considering the noise.)

Transportation and storage

• When transporting the air conditioner, wear shoes with protective toe caps, protective gloves, and other protective clothing.
• When transporting the air conditioner, do not take hold of the bands around the packing carton. You may injure yourself if 

the bands should break.

• When stacking the packing cartons for storage or transportation, heed the precautions written on the packing cartons. 

Failure to heed the precautions may cause the stack to collapse.

• You shall ensure that the air conditioner is transported in stable condition. If you find any part of the product broken, contact 

your dealer.

Installation

• Only a qualified installer(*1) or qualified service person(*1) is allowed to carry out the electrical work of the air conditioner. 

Under no circumstances must this work be done by an unqualified individual since failure to carry out the work properly may 
result in electric shocks and/or electrical leaks.

• After the installation work has been completed, have the installer explain about the circuit breaker positions. In the event 

that error has occurred in the air conditioner, set the circuit breaker to the OFF position, and contact a service person.

• If you install the unit in a small room, take appropriate measures to prevent the refrigerant from exceeding the limit 

concentration even if it leaks. Consult the dealer from whom you purchased the air conditioner when you implement the 
measures. Accumulation of highly concentrated refrigerant may cause an oxygen deficiency accident.

• Do not install the air conditioner in a location that may be subject to a risk of expire to a combustible gas. If a combustible 

gas leaks and becomes concentrated around the unit, a fire may occur.

• Be sure to use the company-specified products for the separately purchased parts. Use of non-specified products may 

result in fire, electric shock, water leakage, etc. Have the installation performed by a professional.

• Confirm that earthing is performed correctly. 

Operation

• Before opening the intake grille of the indoor unit or service panel of the outdoor unit, set the circuit breaker to the OFF 

position. Failure to set the circuit breaker to the OFF position may result in electric shocks through contact with the interior 
parts. Only a qualified installer(*1) or qualified service person(*1) is allowed to remove the intake grille of the indoor unit or 
service panel of the outdoor unit and do the work required.

• Inside the air conditioner are high-voltage areas and rotating parts. Due to the danger of electric shocks or of your fingers 

or physical objects becoming trapped in the rotating parts, do not remove the intake grille of the indoor unit or service panel 
of the outdoor unit. When work involving the removal of these parts is required, contact a qualified installer or a qualified 
service person.

• Do not move or repair any unit by yourself. Since there is high voltage inside the unit, you may get electric shock when 

removing the cover and main unit.

• Use of a stand more than 50 cm high to clean the filter of the indoor unit or to carry out other such jobs constitutes working 

at heights. Due to the danger of falling off the stand and injuring yourself while working at heights, this kind of work should 
not be done by unqualified individuals. When this kind of work must be carried out, do not do it yourself but ask a qualified 
installer or a qualified service person to do it for you.

• Do not touch the aluminum fin of the outdoor unit. You may injure yourself if you do so. If the fin must be touched, do not 

touch it yourself but contact a qualified installer or a qualified service person.

• Do not climb onto or place objects on top of the outdoor unit. You may fall or the objects may fall off of the outdoor unit and 

result in injury.

• Do not place any combustion appliance in a place where it is directly exposed to the wind of air conditioner, otherwise it may 

cause imperfect combustion.

• When the air conditioner is operated with a combustion appliance in the same place, be careful of ventilation to let fresh air 

enter the room. Poor ventilation causes oxygen shortage.

• When the air conditioner is used in a closed room, be careful of sufficient ventilation of the room. Poor ventilation causes 

oxygen shortage.

• Do not expose your body to cool air directly for a long time and do not cool yourself excessively.

Doing so may result in deteriorated physical condition and ill health.

3-EN

4-EN

Summary of Contents for MMY-MAP0501HT8-E

























Reviews: