– 6 –
11-EN
12-EN
EN
EN
ES
EN
■
Operation section
Push each button to select a desired operation.
•
The control saves commands in memory and after the initial setting, there is no need for any additional settings
unless changes are desired. The air conditioner can be operated by pushing the
button.
1 8
3
5
2
9
10
6
7
12
4
11
1
button
Selects the desired Fan speed.
Not available for the high static ducted type.
2
button
Use to setup the timer.
3
button
Use only for service.
(During normal operation, do not use this button.)
4
button
Use when a power ventilation kit (commercially
supplied) is connected.
•
If “
” is displayed on the remote control
when pushing the Ventilation button, no vent kit
connected.
5
button
Resets “ ” display after cleaning
fi
lter.
6
button
Use to activate or deactivate power saving mode.
7
button
Use to select automatic swing or
fi
xed louver
position.
*
Not available for duct type.
8
Operation lamp
Green light illuminates when unit is on.
Although it
fl
ashes when operating the protection
device or a problem occurs.
9
button
When the button is pushed, the operation starts,
and it stops by pushing the button again.
When the operation has stopped, the operation
lamp and all the displays disappear.
10
button
Selects desired operation mode.
11
button
Selects a unit number (left) and louver number
(right).
UNIT :
Selects an indoor unit when adjusting louver
direction when multiple indoor units are controlled
with one remote control.
LOUVER :
Selects a louver when setting louver lock or louver
direction adjustment independently.
*
4-way cassette type only
12
button
Adjusts the set point.
Select the desired set point by pushing TEMP.
or TEMP.
.
OPTION:
Remote control sensor
Usually the temperature sensor of the indoor unit
senses the return air temperature. The temperature
on the surrounding of the remote control can also be
sensed. For details, contact the dealer from which you
have purchased the air conditioner.
4
Correct
usage
When the air conditioner is used for the first time or the setting is changed, follow the steps below. Settings are
saved in memory and are displayed anytime the unit is turned on by pushing the
button.
■
Preparation
When the circuit breaker is turned on, the partition lines are displayed on the remote control.
*
After the circuit breaker is turned on, the remote control does not accept any commands for approx. 1 minute,
this is not a failure.
REQUIREMENT
When the air conditioner is re-powered after it has not been used for a long period, turn on the circuit breaker at
least 12 hours before starting the air conditioner.
SET
TIME
TIMER SET
TEST
FILTER
RESET
TEMP.
CL
FAN
SAVE
SWING/FIX
VENT
MODE
ON / OFF
UNIT LOUVER
1
3
2
4
Start
1
Push
button.
The operation lamp illuminates, and the operation
starts.
2
Select an operation mode with the “
”
button.
The operation mode changes each time the
button is pushed in the order shown below.
Heat
Dry
Fan
Cool
3
Select fan speed with “
” button.
The fan speed changes each time the button is
pushed in the order shown below.
.
Auto
High
Med.
Low
•
When fan is in “
Auto”, fan speed is
adjusted based on difference between set point
and room temperature.
•
In heating operation, if the room temperature
is not heated suf
fi
ciently with volume “ Low”
operation, select “
Med.” or “
High”
operation.
•
The temperature sensor detects the return air
temperature at the indoor unit, which differs
from the room temperature depending on the
installation condition.
Set point is a target of room temperature.
(
“Auto” is not selectable in the Fan mode.)
The fan speed selecting function is not available
for the high static ducted type.
Only “HIGH”
is displayed.
4
Select the set point temperature by
pushing the “TEMP.
” or “TEMP.
”
buttons.
Stop
Push
button.
The operation lamp goes off, and the operation stops.
In the Cool, Dry, or Auto (cooling) mode, the fan runs
for 10 minutes (or more) for self cleaning.
1117907101 EN FR.indb 6
1117907101 EN FR.indb 6
3/21/16 11:44 AM
3/21/16 11:44 AM
