Toshiba P9 ASD Quick Start Manual Download

Page: 26 / 105

P9 ASD Quick Start Guide

Terminal Descriptions

Note:

The programmable terminal assignments may be accessed and changed from the
default settings as mapped on

pg. 40

or via the

Direct Access

method: Program



Direct Access



Applicable Parameter Number

. See the section titled

Program

Mode Menu Navigation on pg. 40

for the applicable

Direct Access

parameter

numbers. For further information on terminal assignments and default setting
changes, see the sections titled

Terminal on pg. 42

and

Default Setting Changes on

pg. 33

Note:

See the section titled

Cable/Terminal/Torque Specifications on pg. 90

for the ASD

conductor and terminal electrical specifications.

— The default setting for this terminal is the

Standby

mode controller. As the default setting, this

terminal must be activated for normal system operation. The

terminal is activated by connecting

to this terminal (Sink mode). When deactivated,

OFF

is flashed on the LED screen and the

Not-Ready-

to-Run

icon is displayed on the LCD screen as shown in

Figure 22 on pg 28

. This input terminal may be

programmed to any of the functions listed in the

P9 ASD Installation and Operation Manual

(See

F113).

RES

— The default setting for this terminal is

Reset

. The

RES

terminal is activated by connecting

to this terminal (Sink mode). A momentary connection to

resets the ASD and any fault indications

from the display.

Reset

is effective when faulted only. This input terminal may be programmed to any

of the functions listed in the

P9 ASD Installation and Operation Manual

(See F114).

— The default setting for this terminal is the

Forward

run command. The

terminal is activated by

connecting

to this terminal (Sink mode). This input terminal may be programmed to any of the

functions listed in the

P9 ASD Installation and Operation Manual

(See F111).

— The default setting for this terminal is the

Reverse

run command. The

terminal is activated by

connecting

to this terminal (Sink mode). This input terminal may be programmed to any of the

functions listed in the

P9 ASD Installation and Operation Manual

(See F112).

— The default setting for this terminal is the

Preset Speed 1

. The

terminal is activated by

connecting

to this terminal (Sink mode). This input terminal may be programmed to any of the

functions listed in the

P9 ASD Installation and Operation Manual

(See F115).

— The default setting for this terminal is the

Preset Speed 2

. The

terminal is activated by

connecting

to this terminal (Sink mode). This input terminal may be programmed to any of the

functions listed in the

P9 ASD Installation and Operation Manual

(See F116).

— The default setting for this terminal is the

Preset Speed 3

. The

terminal is activated by

connecting

to this terminal (Sink mode). This input terminal may be programmed to any of the

functions listed in the

P9 ASD Installation and Operation Manual

(See F117).

— The default setting for this terminal is the

Preset Speed 4

. The

terminal is activated by

connecting

to this terminal (Sink mode). This input terminal may be programmed to any of the

functions listed in the

P9 ASD Installation and Operation Manual

(See F118).

— The default function assigned to this terminal is

Frequency Mode 1

. The

terminal

accepts

0 – 10 VDC input signal that is used to control the function assigned to this terminal. This input terminal
may be programmed to control the speed or torque of the motor via an amplitude setting or regulate by
setting a limit. The gain and bias of this terminal may be adjusted for application-specific suitability
(See F210 – F215).

— The default function assigned to this terminal is

Torque Command

. The

terminal

accepts

±10 VDC input signal that is used to control the function assigned to this terminal. This input terminal
may be programmed to raise or lower the speed or torque of the motor via an amplitude setting or this

tandby

Reset

orward

Reverse

reset Speed 1

reset Speed 2

reset Speed 3

reset Speed 4

requency

Mode 1
RR

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www .ctiautomation.net - Email: info@ctiautomation.net