TEMPORARY OPERATION
TIMER OPERATION
12
Daily timer allows the user to set both the ON & OFF timers and will be
activated on a daily basis.
Setting Daily Timer
Setting the ON Timer
Setting the OFF Timer
1
Press
: Set the desired
ON timer.
Press
: Set the desired
OFF timer.
2
Press
: Set the timer.
Press
: Set the timer.
3
Press
: Cancel the timer.
Press
: Cancel the timer.
●
During the daily timer is activating, both arrows ( , ) are indicated.
Note:
●
Keep the remote control in accessible transmission to the indoor unit;
otherwise, the time lag of up to 15 minutes will occur.
●
The setting will be saved for the next same operation.
1
Press
: Set the ON timer.
3
Press
.
2
Press
: Set the OFF timer.
4
Press
button during
the ( or ) mark
fl
ashing.
Set the timer when the air conditioner is operating.
11
In case of the misplaced or discharged remote control
●
Pressing the RESET button, the unit can start or
stop without using the remote control.
●
Operation mode is set on AUTOMATIC operation,
preset temperature is 24°C and fan operation is
automatic speed.
ECO OPERATION
10
To automatically control room to save energy (except in DRY and FAN ONLY mode)
Press
ECO
: Start and stop the operation.
Note:
Cooling operation; the set temperature will increase automatically 1 degree/
hour for 2 hours (maximum 2 degrees increase). For heating operation the set
temperature will decrease.
PRESET OPERATION
AUTO RESTART OPERATION
To operate at super low fan speed for quiet operation (except in DRY mode)
Press
QUIET
: Start and stop the operation.
Note:
Under certain conditions, QUIET operation may not provide adequate
cooling due to low sound features.
For comfortable sleep, automatically control air
fl
ow and automatically turn OFF.
Press
: Select 1, 3, 5 or 9 hrs for OFF timer operation.
Note:
The cooling operation, the set temperature will increase automatically
1 degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation, the set temperature will decrease.
COMFORT SLEEP OPERATION
16
Firstly, turn off the circuit breaker.
Indoor Unit and Remote Control
●
Clean the indoor unit and the remote control with a wet cloth when needed.
●
No benzine, thinner, polishing powder or chemically-treated duster.
Air
fi
lters
Clean every 2 weeks.
1. Open the air inlet grille.
2. Remove the air
fi
lter.
3. Vacuum or wash and then dry them.
4. Reinstall the air
fi
lters and close the air inlet grille.
MAINTENANCE
17
QUIET OPERATION
15
14
To automatically restart the air conditioner after the power failure (Power of
the unit must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to set
the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for
5 seconds)
2. Press and hold the RESET button on the indoor unit for 3 seconds to
cancel the operation. (3 beep sound but OPERATION lamp does not
blink)
●
In case of ON timer or OFF timer are set, AUTO RESTART OPERATION
does not activate.
13
Set your preferred operation for future use. The setting will be memorized by
the unit for future operation (except air
fl
ow direction).
1. Select your preferred operation.
2. Press and hold
for 3 seconds to memorize the setting.
The
P
mark displays.
3.
Press
: Operate the preset operation.
SELF CLEANING OPERATION
(COOL AND DRY OPERATION ONLY)
18
To protect bad smell caused by the humidity in the indoor unit.
1.
If
the
button is pressed once during “Cool” or “Dry” mode,
the fan will continue to run for other 30 minutes, then it will turn off
automatically. This will reduce the moisture in the indoor unit.
2. To stop the unit immediately, press the
more 2 times within
30 seconds.
The unit does not operate.
Cooling or Heating is abnormally low.
●
The power main switch is
turned off.
●
The circuit breaker is
activated to cut off the
power supply.
●
Stoppage of electric current.
●
ON timer is set.
●
The
fi
lters are blocked with dust.
●
The temperature has been set improperly.
●
The windows or doors are opened.
●
The air inlet or outlet of the outdoor unit
is blocked.
●
The fan speed is too low.
●
The operation mode is FAN or DRY.
TROUBLESHOOTING (CHECK POINT)
20
REMOTE CONTROL A-B SELECTION
21
To separate using of remote control for each indoor unit in case of 2 air
conditioners are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold
button on the Remote Control by the tip of the
pencil. “00” will be shown on the display.
4.
Press
MODE
during pushing
. “B” will show on the display and
“00” will disappear and the air conditioner will turn OFF. The Remote
Control B is memorized.
Note: 1. Repeat above step to reset Remote Control to be A.
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
1
2
OPERATION AND PERFORMANCE
19
1. Three-minute protection feature: To prevent the unit from being activated for 3
minutes when suddenly restarted or switched to ON.
2. Preheating operation: Warm up the unit for 5 minutes before blowing warm air.
3. Warm air control: When the room temperature reaches the set temperature,
the fan speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoor and released into the room.
When the outdoor temperature is too low, use another recommended heating
apparatus in combination with the air conditioner.
6. Consideration for accumulated snow: Select the position for outdoor unit where
it will not be subjected to snow drifts, accumulation of leaves or other seasonal
debris.
7. Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of plastic.
Note:
Item 2 to 6 for Heating model
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature
Room
Temperature
Heating
–15°C ~ 24°C
Less than 28°C
Cooling
–15°C ~ 46°C
21°C ~ 32°C
Dry
–15°C ~ 46°C
17°C ~ 32°C
1118350215_EN.indd 3
1118350215_EN.indd 3
7/12/2559 BE 12:02
7/12/2559 BE 12:02
