Toshiba RAS-16PKVSG-E, Owner'S Manual

1

2

Setting Daily Timer

1

Press 

 : Set the ON timer.

3

Press 

.

2

Press 

 : Set the OFF timer.

4

Press 

 button during 

the (  or  ) mark 

fl

 ashing.

•  During the daily timer is activating, both arrows ( ,  ) are indicated.

Note:

•  Keep the remote control in accessible transmission to the indoor unit; 

otherwise, the time lag of up to 15 minutes will occur.

•  The setting will be saved for the next same operation.

PRESET OPERATION

14

Set your preferred operation for future use. The setting will be memorized by 
the unit for future operation (except air

fl

 ow direction).

1. Select your preferred operation.

2. Press and hold 

 for 3 seconds to memorize the setting.

The 

P

 mark displays.

3. Press 

 : Operate the preset operation.

AUTO RESTART OPERATION

15

To automatically restart the air conditioner after the power failure (Power of 
the unit must be on.)

Setting

1. Press and hold the RESET button on the indoor unit for 3 seconds to 

set the operation. (3 beep sound and OPERATION lamp blink 5 time/
sec for 5 seconds)

2. Press and hold the RESET button on the indoor unit for 3 seconds to 

cancel the operation. (3 beep sound but OPERATION lamp does not 
blink)
•  In case of ON timer or OFF timer are set, AUTO RESTART 

OPERATION does not activate.

To operate at super low fan speed for quiet operation (except in DRY mode)

Press 

48,(7

: Start and stop the operation.

Note:

  Under certain conditions, QUIET operation may not provide adequate 

cooling due to low sound features.

For comfortable sleep, automatically control air 

fl

 ow and automatically turn 

OFF.

Press 

 : Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note:

 The cooling operation, the set temperature will increase automatically 

1 degree/hour for 2 hours (maximum 2 degrees increase). For heating 
operation, the set temperature will decrease.

QUIET OPERATION

16

COMFORT SLEEP OPERATION

17

 Firstly, turn off the circuit breaker.

Indoor Unit and Remote Control

•  Clean the indoor unit and the remote control with a wet cloth when 

needed.

•  No benzine, thinner, polishing powder or chemically-treated duster.

Air 

fi

 lters

Clean every 2 weeks.

1. Open the air inlet grille.
2. Remove the air 

fi

 lters.

3. Vacuum or wash and then dry them.
4. Reinstall the air 

fi

 lters and close the air inlet grille.

MAINTENANCE

18

DISPLAY LAMP BRIGHTNESS ADJUSTMENT

13

To decrease the display lamp brightness or turn it off.

1.  Press and hold 

)$1

 for 3 seconds until brightness level (

, 

, 

 or 

) is shown on remote control LCD then release the button.

2. Press 

Rise

 or 

Decrease

  to adjust brightness in 4 levels.

Remote control 

LCD

Operation display

Brightness

Lamp illuminates full brightness.

100%

Lamp illuminates 50% brightness.

50%

Lamp illuminates 50% brightness and the 
operation lamp is turned off.

50%

All lamps are turned off.

All turned off

●

In the examples of 

 and 

, the lamp illuminates for 5 seconds before 

going off.

SELF CLEANING OPERATION (COOL 
AND DRY OPERATION ONLY)

19

To protect bad smell caused by the humidity in the indoor unit.

1. If the 

 button is pressed once during “Cool” or “Dry” mode, 

the fan will continue to run for other 30 minutes, then it will turn off 
automatically. This will reduce the moisture in the indoor unit.

2. To stop the unit immediately, press the 

 more 2 times within 

30 seconds.

OPERATION AND PERFORMANCE

20

The unit does not operate.

Cooling or Heating is abnormally low.

•  The power main switch is 

turned off.

•  The circuit breaker is 

activated to cut off the power 
supply.

•  Stoppage of electric current
•  ON timer is set.

• The 

fi

 lters are blocked with dust.

•  The temperature has been set 

improperly.

•  The windows or doors are opened.
•  The air inlet or outlet of the outdoor 

unit is blocked.

•  The fan speed is too low.
•  The operation mode is FAN or DRY.

TROUBLESHOOTING (CHECK POINT)

21

REMOTE CONTROL A-B SELECTION

22

To separate using of remote control for each indoor unit in case of 2 air 
conditioners are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold 

 button on the Remote Control by the tip of the 

pencil. “00” will be shown on the display. (Picture 

1

)

4. Press 

02'(

 during pushing 

. “B” will show on the display and 

“00” will disappear and the air conditioner will turn OFF. The Remote 
Control B is memorized. (Picture 

2

)

Note:

  1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not “A” display.

3. Default setting of Remote Control from factory is A.

1. Three-minute protection feature: To prevent the unit from being activated 

for 3 minutes when suddenly restarted or switched to ON.

2. Preheating operation: Warm up the unit for 5 minutes before the heating 

operation starts.

3. Warm air control: When the room temperature reaches the set 

temperature, the fan speed is automatically reduced and the outdoor unit 

will stop.

4. Automatic defrosting: Fans will stop during defrost operation.

5. Heating capacity: Heat is absorbed from outdoors and released into 

the room. When the outdoor temperature is too low, use another 

recommended heating apparatus in combination with the air conditioner.

6. Consideration for accumulated snow: Select the position for outdoor unit 

where it will not be subjected to snow drifts, accumulation of leaves or 

other seasonal debris.

7. Some minor cracking sound may occur when unit operating. This is 

normal because the cracking sound may be caused by expansion/

contraction of plastic.

Note:

 Item 2 to 6 for Heating model

Air conditioner operating conditions

Temp.

Operation

Outdoor Temperature

Room Temperature

Heating

–15°C ~ 24°C

Less than 28°C

Cooling

–15°C ~ 46°C

21°C ~ 32°C

Dry

–15°C ~ 46°C

17°C ~ 32°C

EN