background image

4

REQUIREMENT OF REPORT TO THE LOCAL POWER SUPPLIER

Please make absolutely sure that the installation of this appliance is reported to 
the local power supplier before installation. If you experience any problems or if the 
installation is not accepted by the supplier, the service agency will take adequate 
countermeasures.

 

Important information regarding the refrigerant used

  This product contains 

fl

 uorinated greenhouse gases. 

  Do not vent gases into the atmosphere.
 Refrigerant 

type: 

R32

 GWP

(1)

 value: 

675

 * (ex. R32 ref. AR4)

 

(1)

GWP = global warming potential

  The refrigerant quantity is indicated on the unit name plate.
  * This value is based on F gas regulation 517/2014 

CAUTION

• Exposure of unit to water or other moisture before installation could result in 

electric shock.

  Do not store it in a wet basement or expose to rain or water.
• After unpacking the unit, examine it carefully for possible damage.
• Do not install the unit at place where leakage of 

fl

 ammable gas may occur. In 

case gas leaks and accumulates at surrounding of the unit, it may cause of 

fi

 re.

• Do not install in a place that can increase the vibration of the unit. Do not 

install in a place that can amplify the noise level of the unit or where noise and 
discharged air might disturb neighbors.

• To avoid personal injury, be careful when handling parts with sharp edges.
• Please read this installation manual carefully before installing the unit. It contains 

further important instructions for proper installation.

• The manufacturer shall not assume any liability for the damage caused by not 

observing the description of this manual.

Summary of Contents for RAS-18PAVSG-E























Reviews: