4
5
"
!
1
2
7
8
#
3
9
6
EN
CT
1
Press
FIX
: Move the louver in
the desired vertical direction.
2
Press
SWING
: Swing the air
automatically and press again to stop.
3
For horizontal direction, adjust
manually.
AIR FLOW DIRECTION
3
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
AUTOMATIC OPERATION
5
To automatically select cooling or fan only operation
1.
Press
MODE
: Select A.
2.
Press
: Set the desired temperature.
3.
Press
FAN
: Select AUTO, LOW , LOW+
, MED
,
MED+
, or HIGH
.
REMOTE CONTROL
4
PREPARATION BEFORE USE
2
1
Infrared signal emitter
2
Start/Stop button
3
Mode select button (MODE)
4
Temperature button (TEMP)
5
Fan speed button (FAN)
6
Swing louver button (SWING)
7
Set louver button (FIX)
8
Off timer button (OFF)
9
High power button (Hi-POWER)
!
Economy button (ECO)
"
Clear button (CLEAR)
#
Check button (CHECK)
Preparing Filters
1. Open the air inlet grille and remove the air
fi
lters.
2.
Attach
the
fi
lters. (see detail in the accessory sheet).
Loading Batteries (when use wireless operation.)
1. Remove the slide cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Remote Control Reset
1. Remove the batteries.
2.
Press
.
3. Insert the batteries.
TEMPORARY OPERATION
TIMER OPERATION
11
Setting the OFF timer
1
Press
OFF
for enter OFF timer setting.
2
Press
for select desired OFF timer. (0.5 - 12 hrs)
3
Press
OFF
for set OFF timer.
4
Press
OFF
again for cancel OFF timer.
Set the timer when the air conditioner is operating.
10
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or
stop without using the remote control.
• Operation mode is set on AUTOMATIC
operation, preset temperature is 24°C and fan
operation is automatic speed.
COOLING / FAN ONLY OPERATION
DRY OPERATION
7
For dehumidi
fi
cation, a moderate cooling performance is controlled automatically.
1.
Press
MODE
: Select Dry
.
2.
Press
: Set the desired temperature.
6
1.
Press
MODE
: Select Cool
or Fan only
.
2.
Press
: Set the desired temperature.
Cooling: Min. 17°C, Fan Only: No temperature indication
3.
Press
FAN
: Select AUTO, LOW , LOW+
, MED
,
MED+
, or HIGH
.
Hi-POWER OPERATION
ECO OPERATION
9
To automatically control room to save energy (except in DRY and FAN ONLY mode)
Press
: Start and stop the operation.
Note:
Cooling operation; the set temperature will increase automatically 1
degree/hour for 2 hours (maximum 2 degrees increase).
8
To automatically control room temperature and air
fl
ow for faster cooling
operation (except in DRY and FAN ONLY mode)
Press
Hi POWER
: Start and stop the operation.
AUTO RESTART OPERATION
Firstly, turn off the circuit breaker.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when
needed.
• No benzine, thinner, polishing powder or chemically-treated duster.
MAINTENANCE
13
12
To automatically restart the air conditioner after the power failure (Power of
the unit must be on.)
Setting
1. Press and hold the RESET button on the indoor unit for 3 seconds to set
the operation. (3 beep sound and OPERATION lamp blink 5 time/sec for
5 seconds)
2. Press and hold the RESET button on the indoor unit for 3 seconds to
cancel the operation. (3 beep sound but OPERATION lamp does not
blink)
• In case of ON timer or OFF timer are set, AUTO RESTART
OPERATION does not activate.
1110255132_EN.indd 3
1110255132_EN.indd 3
3/2/2559 BE 16:35
3/2/2559 BE 16:35
