– 59 –
Filter sign setting
According to the installation condition, the filter sign
term (Notification of filter cleaning) can be changed.
Follow to the basic operation procedure
(
1
2
3
4
5
6
).
• For the CODE No. in Procedure
3
, specify
[01]
.
• For the [SET DATA] in Procedure
4
, select the SET
DATA of filter sign term from the following table.
To secure better effect of
heating
When it is difficult to obtain satisfactory heating due to
installation place of the indoor unit or structure of the
room, the detection temperature of heating can be
raised. Also use a circulator or other device to circulate
heat air near the ceiling.
Follow to the basic operation procedure
(
1
2
3
4
5
6
).
• For the CODE No. in Procedure
3
, specify
[06]
.
• For the set data in Procedure
4
, select the SET
DATA of shift value of detection temperature to be
set up from the following table.
How to set up swing type
1. Push
for at least four seconds when the air
conditioner is not working.
flashes.
Indicates CODE No.
[F0]
.
2. Select an indoor unit to be set by pushing
(left side of the button).
Each time you push the button, unit numbers
change as follows:
The fan of the selected unit runs and the louvers
start swinging.
3. Select a swing type by pushing “TIME”
buttons.
CAUTION
CAUTION
Do not set the swing SET DATA to “
0000
”.
(This setting may cause a failure of the louvers.)
SET DATA
Filter sign term
0000
None
0001
150 H
0002
2500 H
(Factory default)
0003
5000 H
0004
10000 H
SET DATA
Detection temperature shift value
0000
No shift
0001
+1°C
0002
+2°C
(Factory default)
0003
+3°C
0004
+4°C
0005
+5°C
0006
+6°C
Swing SET DATA
Swing of louvers
0001
Standard swing
(Factory default)
0002
Dual swing
0003
Cycle swing
No
display
UNIT No.
1-1
UNIT No.
1-2
UNIT No.
1-3
UNIT No.
1-4
Swing SET DATA
•
About “Dual swing”
“Dual” means that louvers
01
and
03
are directed
and swing in one direction and louvers
02
and
04
are
directed and swing in the opposite direction.
(When louvers
01
and
03
are directed downward,
louvers
02
and
04
are directed horizontally.)
•
About “Cycle swing”
The four louvers swing independently at respective
timings.
4. Push
button.
5. Push
button to complete the setting.
How to set up louver lock
(No swing)
1. Push
(right side of the button) for at least
four seconds when the air conditioner is not working.
flashes.
Indicates CODE No.
[F1]
.
2. Select an indoor unit to be set by pushing
(left side of the button).
Each time you push the button, unit numbers
change as follows:
The fan of the selected unit runs and the louvers
start swinging.
3. Select a louver you want to lock by pushing “TEMP.”
buttons.
4. Select the wind direction of the louver you do not
want to swing by pushing “TIME”
buttons.
* When (4) or (5) is selected, dew drop may occur
during cooling mode.
5. Determine the setting by pushing
button.
When the setting has been determined,
lights
up.
6. Push
button to complete the setting.
01
03
04
02
Indoor unit
drain pipe
Indoor unit
refrigerant pipe
Electrical
control box
UNIT No.
1-1
UNIT No.
1-2
UNIT No.
1-3
UNIT No.
1-4
(1)
0001
(2)
0002
(3)
0003
(5)
0005
(4)
0004
SET DATA
0001-0005
(Louver lock position code)
117-EN
118-EN
