background image

4-EN

3-EN

– 2 –

EN

De

fi

nition of Protective Gear

When the air conditioner is to be transported, installed, maintained, repaired or removed, wear protective gloves 
and “Safety” work clothing.
In addition to such normal protective gear, wear the protective gear described below when undertaking the special 
work detailed in the table below.
Failure to wear the proper protective gear is dangerous because you will be more susceptible to injury, burns, 
electric shocks and other injuries.

Work undertaken

Protective gear worn

All types of work

Protective gloves
“Safety” working clothing

Electrical-related 
work

Gloves to provide protection for electricians and from heat
Insulating shoes
Clothing to provide protection from electric shock

Work done at heights 
(50 cm or more)

Helmets for use in industry

Transportation of 
heavy objects

Shoes with additional protective toe cap

Repair of outdoor unit

Gloves to provide protection for electricians and from heat

„

 

Center of gravity

(Unit : mm)

150

295

335

Center of gravity

Center of gravity

Thank you for purchasing this Toshiba air conditioner.
Please read carefully through these instructions that contain important information which complies with the 
Machinery Directive (Directive 2006/42/EC), and ensure that you understand them.
After reading these instructions, be sure to keep them in a safe place together with the Owner’s Manual and 
Installation Manual supplied with your product.

Generic Denomination: Air Conditioner

De

fi

nition of Quali

fi

ed Installer or Quali

fi

ed Service Person

The air conditioner must be installed, maintained, repaired and removed by a quali

fi

ed installer or quali

fi

ed service 

person. When any of these jobs is to be done, ask a quali

fi

ed installer or quali

fi

ed service person to do them for you. 

A quali

fi

ed installer or quali

fi

ed service person is an agent who has the quali

fi

cations and knowledge described in 

the table below.

Agent

Quali

fi

cations and knowledge which the agent must have

Quali

fi

ed installer

• The quali

fi

ed installer is a person who installs, maintains, relocates and removes the air conditioners made 

by Manufacturer. He or she has been trained to install, maintain, relocate and remove the air conditioners 
made by Manufacturer or, alternatively, he or she has been instructed in such operations by an individual 
or individuals who have been trained and is thus thoroughly acquainted with the knowledge related to 
these operations.

• The quali

fi

ed installer who is allowed to do the electrical work involved in installation, relocation and 

removal has the quali

fi

cations pertaining to this electrical work as stipulated by the local laws and 

regulations, and he or she is a person who has been trained in matters relating to electrical work on the 
air conditioners made by Manufacturer or, alternatively, he or she has been instructed in such matters by 
an individual or individuals who have been trained and is thus thoroughly acquainted with the knowledge 
related to this work.

• The quali

fi

ed installer who is allowed to do the refrigerant handling and piping work involved in installation, 

relocation and removal has the quali

fi

cations pertaining to this refrigerant handling and piping work 

as stipulated by the local laws and regulations, and he or she is a person who has been trained in 
matters relating to refrigerant handling and piping work on the air conditioners made by Manufacturer or, 
alternatively, he or she has been instructed in such matters by an individual or individuals who have been 
trained and is thus thoroughly acquainted with the knowledge related to this work.

• The quali

fi

ed installer who is allowed to work at heights has been trained in matters relating to working at 

heights with the air conditioners made by Manufacturer or, alternatively, he or she has been instructed in 
such matters by an individual or individuals who have been trained and is thus thoroughly acquainted with 
the knowledge related to this work.

Quali

fi

ed service 

person

• The quali

fi

ed service person is a person who installs, repairs, maintains, relocates and removes the air 

conditioners made by Manufacturer. He or she has been trained to install, repair, maintain, relocate and 
remove the air conditioners made by Manufacturer or, alternatively, he or she has been instructed in such 
operations by an individual or individuals who have been trained and is thus thoroughly acquainted with the 
knowledge related to these operations.

• The quali

fi

ed service person who is allowed to do the electrical work involved in installation, repair, 

relocation and removal has the quali

fi

cations pertaining to this electrical work as stipulated by the local 

laws and regulations, and he or she is a person who has been trained in matters relating to electrical 
work on the air conditioners made by Manufacturer or, alternatively, he or she has been instructed in such 
matters by an individual or individuals who have been trained and is thus thoroughly acquainted with the 
knowledge related to this work.

• The quali

fi

ed service person who is allowed to do the refrigerant handling and piping work involved in 

installation, repair, relocation and removal has the quali

fi

cations pertaining to this refrigerant handling and 

piping work as stipulated by the local laws and regulations, and he or she is a person who has been trained 
in matters relating to refrigerant handling and piping work on the air conditioners made by Manufacturer or, 
alternatively, he or she has been instructed in such matters by an individual or individuals who have been 
trained and is thus thoroughly acquainted with the knowledge related to this work.

• The quali

fi

ed service person who is allowed to work at heights has been trained in matters relating to 

working at heights with the air conditioners made by Manufacturer or, alternatively, he or she has been 
instructed in such matters by an individual or individuals who have been trained and is thus thoroughly 
acquainted with the knowledge related to this work.

Summary of Contents for RAV-GV1101AT8P-E



























Reviews: