background image

6-EN

5-EN

– 3 –

Warning indication

Description

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote 
electric power supplies 
before servicing.

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect all remote electric power supplies before 
servicing.

These safety cautions describe important matters concerning safety to prevent injury to users or other people 
and damages to property. Please read through this manual after understanding the contents below (meanings of 
indications), and be sure to follow the description.

Indication

Meaning of Indication

 WARNING

Text set off in this manner indicates that failure to adhere to the directions in the warning 
could result in serious bodily harm (*1) or loss of life if the product is handled improperly.

 CAUTION

Text set off in this manner indicates that failure to adhere to the directions in the caution 
could result in slight injury (*2) or damage (*3) to property if the product is handled 
improperly.

*1:  Serious bodily harm indicates loss of eyesight, injury, burns, electric shock, bone fracture, 

poisoning, and other injuries which leave aftereffect and require hospitalization or long-term 
treatment as an outpatient.

*2:  Slight injury indicates injury, burns, electric shock, and other injuries which do not require 

hospitalization or long-term treatment as an outpatient.

*3:  Damage to property indicates damage extending to buildings, household effects, domestic livestock, 

and pets.

„

 

Warning indications on the Air Conditioner Unit

WARNING

(Risk of 

fi

re)

This mark is for R32 refrigerant only. Refrigerant type is written on 
nameplate of outdoor unit.
In case that refrigerant type is R32, this unit uses a 

fl

ammable 

refrigerant.
If refrigerant leaks and comes in contact with 

fi

re or heating part, it will 

create harmful gas and there is risk of 

fi

re.

Read the OWNER’S MANUAL carefully before operation.

Service personnel are required to carefully read the OWNER’S MANUAL and 
INSTALLATION MANUAL before operation.

Further information is available in the OWNER’S MANUAL, INSTALLATION MANUAL, 
and the like.

WARNING

Moving parts.
Do not operate unit with grille 
removed.
Stop the unit before the servicing.

WARNING

Moving parts.

Do not operate unit with grille removed.
Stop the unit before the servicing.

WARNING

Capacitor connected within 
this disconnect or 
downstream upon shutdown 
wait 5 minutes to allow 
capacitors to discharge

WARNING

Capacitor connected within this disconnect or downstream 
upon shutdown wait 5 minutes to allow capacitors to 
discharge.

CAUTION

High temperature parts.
You might get burned 
when removing this panel.

CAUTION

High temperature parts.
You might get burned when removing this panel.

CAUTION

Do not touch the aluminum 
fins of the unit.
Doing so may result in injury.

CAUTION

Do not touch the aluminium 

fi

ns of the unit.

Doing so may result in injury.

CAUTION

BURST HAZARD

Open the service valves before 
the operation, otherwise there 
might be the burst.

CAUTION

BURST HAZARD

Open the service valves before the operation, otherwise there 
might be the burst.

CAUTION

Do not touch the aluminum 
fins of the unit.
You might get burned.

CAUTION

Do not touch the aluminium 

fi

ns of the unit.

You might get burned.

Summary of Contents for RAV-GV1101AT8P-E



























Reviews: