Toshiba RAV-HM1101FT-TR, Installation Manual

– 23 –

Address is displayed here.

Address is displayed here.

6

Push the [

 MENU] button to set the other 

Code (DN) and Data. After “Continue?” is 

displayed on the screen, push the 

“

 Yes” [ F1] button.

Indoor address change



Change “Code (DN)” from [0010] to [0013] with 

the [ 

∧

] / [ 

∨

 ] button.



Change “Data” from [0003] to [0002] with the

 [ 

∧

] / [ 

∨

 ] button.

7

Push the [

 MENU] button to set the other 

Code (DN) and Data. After “Continue?” is 

displayed on the screen, push the 

“

 Yes” [ F1] button.

Group address change



Change “Code (DN)” from [0010] to [0014] with 

the [ 

∧

] / [ 

∨

 ] button.



Change “Data” from [0001] to [0002] with the

 [ 

∧

] / [ 

∨

 ] button.

8

Push the [

 MENU] button to set the other 

Code (DN) and Data. After “Continue?” is 

displayed on the screen, push the 

“

No” [  F2]  button to finish the 

setting operation. “ Setting” appears on 

the screen for a while, then the screen 

returns to the “Field setting menu” screen.



Pushing the “

No” [   F2] button 

displays the unit selection screen when the 

group control is used. Push the [ 

 CANCEL] 

button on the unit selection screen to finish the 

setting operation. “  Setting” appears on the 

screen for a while, then the screen returns to the 

“Field setting menu” screen.

DN setting

Code

Data

3-3

Return

0013

0003

Fix

<

>

(DN) I.DN

DN setting

Code

Data

3-3

Return

Fix

<

>

0002

0013

(DN) I.DN

DN setting

Code

Data

3-3

Return

0014

0001

Fix

<

>

(DN) I.DN

DN setting

Code

Data

3-3

Return

Fix

<

>

0002

0014

(DN) I.DN

Yes

Yes

No

No

9

Test run



Before test run

• Before turning on the power supply, carry out the following procedure.

1) By using tester (500 VM

Ω

), check that resistance of 1 M

Ω

 or more exists between the terminal block 1 to 

3 and the earth (grounding).

If resistance of less than 1 M

Ω

 is detected, do not run the unit.

2) Check the valve of the outdoor unit being opened fully.

• To protect the compressor at activation time, leave power-ON for 12 hours or more before operating.



Execute a test run

Operate the unit with the remote controller as usual.

For the procedure of the operation, refer to the attached Owner’s Manual.

A forced test run can be executed in the following procedure even if the operation stops by thermostat-OFF.

In order to prevent a serial operation, the forced test run is released after 60 minutes have passed and returns to 

the usual operation.

CAUTION

• Do not use the forced test run for cases other than the test run because it applies an excessive load to the devices.

• Be careful of fan operation when the circuit breaker is turned on. If the refrigerant leak detection sensor detects the 

refrigerant leak, a fan automatically rotates even while an air conditioner stops. Be careful not to be injured by the fan.

1

Push the [

MENU] button to display the 

menu screen.

2

Push and hold the [

MENU] button and 

the [

∨

] button at the same time to 

display the “Field setting menu”.



Push and hold the buttons for more than 4 

seconds.

3

Push the [

∧

 ] / [

∨

] button to select 

“1. Test mode” on the “Field setting menu” 

screen, then push the “

 Set” [

F2] button.



Pushing the “

Yes” [  F1] button 

sets the test mode and the screen returns to the 

“Field setting menu” screen.

Push [

 CANCEL] twice, the screen (2) 

appears.

1.Test mode

2.Register service info.

3.Alarm history

4.Monitor function

5.Setting louver position

Field setting menu(1/2)

Return

Set

1.Test mode

2.Register service info.

3.Alarm history

4.Monitor function

5.Setting louver position

Field setting menu(1/2)

Return

Set

Set

Yes

Return

Test mode start.

No

Yes

Test mode

45-EN

46-EN