11-EN
12-EN
– 6 –
■
Wireless remote controller
•
A place where there are no obstacles such as a curtain that may block the signal from the indoor unit.
•
Do not install the remote controller in a place exposed to direct sunlight or close to a heating source, such as a
stove.
•
Keep the remote controller at least 1 m apart from the nearest TV set or stereo equipment.
(This is necessary to prevent image disturb-bounces or noise interference.)
•
The location of the remote controller should be determined as shown below.
* 7 m
5 m
5
m
7 m
75
°
45°
45
°
(Side view)
(Top view)
Remote controller
Reception
range
Reception range
* : Axial distance
Indoor unit
Indoor unit
Remote controller
4
Installation
WARNING
Install the air conditioner certainly to suf
fi
ciently withstand the weight.
If the strength is insuf
fi
cient, the unit may fall down resulting in human injury.
Perform a speci
fi
ed installation work to guard against strong wind or earthquake.
An incomplete installation can cause accidents by the units falling and dropping.
REQUIREMENT
Strictly comply with the following rules to prevent damage of the indoor units and human injury.
•
Do not put a heavy article on the indoor unit. (even units are packaged)
•
Carry in the indoor unit as it is packaged if possible. If carrying in the indoor unit unpacked by necessity, be
sure to use buffering cloth, etc. to not damage the unit.
•
To move the indoor unit, do not apply force to the refrigerant pipe, drain pan, foamed parts, or resin parts, etc.
•
Carry the package by two or more persons, and do not bundle it with plastic band at positions other than
speci
fi
ed.
Be careful to the following items when installing the unit.
•
Considering air discharge direction, select an installation place where discharge air can circulate evenly in a
room. Avoid to install the unit at place with “
NO GOOD
” mark in the right figure.
OK
NO
GOOD
: Not cooled well.
Good installation place
Cooled well all over.
Bad installation place
Screen
■
Cutting a hole
In case of installing the refrigerant pipes from the rear:
1
Decide the hole position for piping at
100 mm from the arrow mark ( ) on the
installation plate and drill a hole at a slight
downward slant toward outdoor side.
80
100
180
Ø65 mm
100 mm
The centre of the pipe hole
is above the arrow
Pipe hole
NOTE
When drilling a wall that contains a metal lath, wire
lath or metal plate, be sure to use a pipe hole brim
ring sold separately.
■
Mounting the installation plate
62
82.5
170
85
Be sure that the installation plate is
fi
x to the wall
with screws to make the indoor unit
fi
t to the wall.
Anchor bolt holes
Hook
Pipe hole
Hook
Hook
Indoor unit
Thread
Weight
Mounting
Screw
Installation
plate
Pipe hole
2 m or more from
fl
oor
■
When the installation plate is
directly mounted on the wall
1
Securely
fi
t the installation plate onto the
wall by screwing it in the upper and lower
parts to hook up the indoor unit.
2
To mount the installation plate on a
concrete wall with anchor bolts, utilize
the anchor bolt holes as illustrated in the
above
fi
gure.
3
Install the installation plate horizontally in
the wall.
CAUTION
When installing the installation plate with a mounting
screw, do not use the anchor bolt hole.
Otherwise the unit may fall down and result in
personal injury and property damage.
Projection
15 mm or less
Clip anchor
(local parts)
Mounting screw
4 × 25
Anchor bolt
5 mm dia. hole
NO
GOOD
NO
GOOD
OK
CAUTION
Failure to
fi
rmly install the unit may result in personal
injury and property damage if the unit falls.
•
In case of block, brick, concrete or similar type walls,
make 5 mm dia. holes in the wall.
•
Insert clip anchors for appropriate mounting screws.
NOTE
Secure four corners and lower parts of the installation
plate with 6 mounting screws to install it.
5
Cutting a hole and mounting installation
plate
1111056499_(01)_EN.indb 6
1111056499_(01)_EN.indb 6
10/13/14 9:13 AM
10/13/14 9:13 AM
