English
─
EB01101501
3
Correct usage
When you use the air conditioner for the first time or change the settings, follow the procedures below.
From next time, pushing the ON/OFF button starts running of the air conditioner with the chosen settings.
Cooling only models cannot do automatic operation (AUTO) and heating.
* See the Owner's Manual for the indoor unit regarding the operating limits of the functions for each button.
Standby
Operations are not accepted when “SETTING” is blinking.
REQUIREMENT
• Keep the power switch turned on during use.
• When you resume using the air conditioner after a long period of disuse, turn on the power switch at least 12 hours
before starting running.
Operations
1
ON/OFF button
Push the button to light the operation lamp and start
operations.
When heating
• The heated air comes out after a 3 to 5 minutes of
pre-heating with the indoor fan kept turned off.
2
Mode select button
Each time you push the button, the operation mode
and its icon change in the following order:
(The indicator on the cooling only models does not
show: “
Auto” and “
Heat”)
• For the multi-system, only Super Heat Recovery
Multi “
Auto” can be displayed and selected.
• With the Concealed Duct High Static Pressure
Type, “
Dry” is not available.
3
Fan speed button
Each time you push the button, fan speed and its
indication change in the following order:
• “
Auto” cannot be selected in the Fan mode.
• It becomes “
Fix” for the Concealed Duct High
Static Pressure Type and other models that cannot
select the fan speed, so fan speed is fixed.
4
Temperature setting button
While the room temperature is being shown,
push the temperature button to change LCD from
to and select the desired set point.
The temperature setting range is 18.0 °C to 29.0 °C.
• LCD shows room temperature 5 seconds after
the temperature button was pushed.
• To change the set temperature, push the
temperature button again to change LCD to and
select the desired set point.
• Contact your dealer for information on how to
switch the temperature indicator.
5
Set louver and swing button
• Refer to the Owner's Manual for the indoor unit
regarding the set louver and swing button, because
there is a slight difference depending on the model
of the indoor unit.
1
4
5
2
3
Dry
Cool
Fan
(Dehumidify)
Auto
Heat
Low
Medium
High
Auto
Stopping
Push ON/OFF button
Push the button to turn off the operation lamp and stop operations.
• The air conditioner may continue running in the fan mode for about 30 seconds after stopping heating.
• After stopping operations, do not restart operations for about 3 minutes, to protect the machinery.
4
Troubleshooting
Confirmation and check
Troubleshooting history and confirmation
You can check the troubleshooting history with the following procedure if a problem occurs with the air conditioner.
(The troubleshooting history records up to 4 incidents.)
You can check it during operation or when operation is stopped.
5
When requesting repairs
Contact us the combination of alphabet (A, E, F, H, L, P) and numbers that appear on the check code of the LCD of the
remote controller too.
If a problem occurs with the air conditioner, the
temperature setting indicator alternately shows
the check code and the indoor Unit No. in which
the problem occurred.
Procedure
Description of operation
1
Push the
+ temperature
buttons at the same time for over 4 seconds
and the indicators appear as an image indicating the troubleshooting history
mode has been entered.
• [01: Order of troubleshooting history] appears in the temperature indicator.
• The check code indicator alternately shows the [check code] and the [indoor
Unit No. in which the problem occurred].
2
Each time the temperature setting temperature button is pushed, the recorded
troubleshooting history is displayed in sequence.
The troubleshooting history appears in order from [01] (newest) to [04] (oldest).
REQUIREMENT
In the troubleshooting history mode, do not push the
+ temperature
buttons at the same time for over 4 seconds, doing so deletes the entire
troubleshooting history of the indoor unit.
3
After you have finished checking, push the
button with a long thin pencil or
something, to return to the regular mode.
Check code
The indoor Unit No. in which
the problem occurred.
TEST
1
2
3
TEST
TEST
+01EN01BODY.fm Page 2 Friday, December 21, 2012 10:46 AM
