– 2 –
Test run
1.
Turn on the power of the air conditioner. When power is turned on for the first
time after installation, it takes approx. 5 minutes until the remote controller
becomes available. In the case of subsequent power-on, it takes approx. 1
minute until the remote controller becomes available. Execute a test run after
the predetermined time has passed.
2.
Push “ON/OFF” button on the remote controller, select [
Cool] or [
Heat] with “MODE” button, and then select
[
HIGH] with “FAN” button.
3.
4.
5.
6.
Repeat procedures
4
5
4
5
. Indicators “Operation” (green),
“Timer” (green), and “Ready” (orange) in the wireless receiver section flash in
approx. 10 seconds, and the air conditioner starts operation. If any of these
indicators does not flash, repeat procedures 2 to 5.
7.
Upon completion of the test run, push
“ON/OFF” button to stop operation.
<Overview of test run operations using the wireless remote controller>
▼
Cooling test run:
ON/OFF
17°C
18°C
17°C
18°C
17°C
18°C
17°C
(test run)
ON/OFF
▼
Heating test run:
ON/OFF
30°C
29°C
30°C
29°C
30°C
29°C
30°C
(test run)
ON/OFF
Wireless remote controller A-B selection
Using 2 wireless remote controllers for the respective air conditioners, when the 2 air
conditioners are closely installed.
Wireless remote controller B setup
1.
Push the START/STOP button to operate the air conditioner. Push it again to stop
the air conditioner.
2.
Push
[Temporary] button on the signal receiving unit to operate the air conditioner.
3.
Point the wireless remote controller at the indoor unit.
4.
Push and hold
button on the wireless remote controller by the tip of the
pencil. “00” will be shown on the display.
5.
Push the MODE
button during pushing
.
“B” will be shown on the display and “00” will be disappear and the air conditioner
will turn OFF. The wireless remote controller B is memorized.
Note:
• Repeat above step to reset wireless remote controller to be A.
• The wireless remote controllers do not display “A”.
• The factory default of the wireless remote controllers is “A”.
Cooling test run
Heating test run
Set the temperature to 17°C with the temp.
setup buttons.
Set the temperature to 30°C with the temp.
setup buttons.
Cooling test run
Heating test run
After confirming a signal receiving sound
“beep” immediately set the temperature to
18°C with the temp. setup buttons.
After confirming a signal receiving sound
“beep” immediately set the temperature to
29°C with the temp. setup buttons.
Cooling test run
Heating test run
After confirming a signal receiving sound
“beep” immediately set the temperature to
17°C with the temp. setup buttons.
After confirming a signal receiving sound
“beep” immediately set the temperature to
30°C with the temp. setup buttons.
CHK
MODE
CHK
“B” Display
“00” Display
Temporary
button
How to handle the remote controller
•
To set the remote controller on the wall
Push button at the installation position on the wall to check that the signal from the
remote controller is received correctly.
• Loading Batteries
1.
Remove the battery cover.
2.
Insert 2 new batteries (R03 [AAA]) following the (+)
and (-) positions.
Self-diagnosis function and measures
• The following table shows a few examples. For details of indoor unit errors, refer to
the Installation Manual of the indoor unit.
LEDs on the signal receiving unit : OFF
: Blinking (at intervals of 0.5 seconds)
LED color : Green : Green : Orange
Notes on installing remote controller
• When using a wireless remote controller in the remote controller holder on a wall,
turn on a fluorescent light and operate the remote controller at the installation
position. Make sure that the air conditioner operates normally and then secure the
remote controller holder on the wall.
• When installing a remote controller that senses room temperature with the sensor,
avoid the following places.
• A place exposed to direct cool air, warm air or direct sunlight
• A place subject to thermal effects
Explanation to the customer
• After the installation work has been completed, execute a test run to check for normal
operation and then hand the customer the Owner’s Manual and Installation Manual of
the wireless remote controller kit.
• Explain how to use and maintain the wireless remote controller kit to the customer
according to the Owner’s Manual of the wireless remote controller kit.
LED
Possible cause
Measures
These LEDs do not light or blink
even if the remote controller is
operated.
- Power is not turned on.
- Incorrect connection between
signal receiving unit and indoor
unit
Check connections and
reconnect wires correctly, if
necessary.
Loose connection between signal
receiving unit and indoor unit
Incorrect or loose connection
between indoor unit and outdoor
unit
The protective device of the
outdoor unit is activated.
Check the outdoor unit.
The protective device of the
indoor unit is activated.
Check the indoor unit.
1
2
Tapping screw
M4 × 16 mm
Remote controller holder
Remote
controller
Remote
controller holder
Push
Put on.
A
C
L
EB99814001
Precaution that the test run method in
wireless remote controller differs from other
indoor units.
