background image

– 13 –

Wireless remote controller 
A-B selection

Using 2 wireless remote controllers for the respective air 
conditioners, when the 2 air conditioners are closely 
installed.

Wireless remote controller B setup

1. Start the air conditioner.
2. Point the wireless remote controller at the 

indoor unit.

3. Push and hold 

 button on the wireless 

remote controller by the tip of the pencil.
“00” will be shown on the display.

4. Push MODE 

 button during pushing 

“B” will be shown on the display and “00” will 
be disappear and the air conditioner will turn 
OFF. The wireless remote controller B is 
memorized.

NOTE

• Repeat above step to reset wireless remote 

controller to be A.

• The wireless remote controllers do not display “A”.
• The factory default of the wireless remote controllers 

is “A”.

• A-B selection can be set with signal receiving unit. 

For the further details, refer to the installation 
manual.

9

Operating air conditioner without remote 

controller

In the following cases, the air conditioner can be operate without remote controller with temporary operation 
button on the signal receiving unit.

• The battery in the remote controller expired.
• A trouble occurred on the remote controller.
• The remote controller has been lost.

1

Start

Push temporary operation button.
• The operation mode is the one last selected.

If you want to change it, turn the power off and 
then on, and push the temporary operation button 
again.

2

Stop

Push temporary operation button once more.

CHK

CHK

PRESET

FAN

"B" Display

"00" Display

1

2

13-EN

+EH99950501.BOOK  Page 13  Thursday, June 18, 2015  10:57 AM

Summary of Contents for RBC-AX32UW-UL

















Reviews: