background image

E65807

1

8

 

‑ 

‑ 

‑ 

‑ 

3 ‑

About operation

 

Danger

Prohibited

 

Do not wipe the body with a wet cloth.

      It could lead to electric shocks.

  Do not pull on the cable

      It could cause damage or error.

About disposal of the product

 Cautions

Mandatory

 

Dispose of the product as an industrial waste.

      Unless it is disposed of as an industrial waste, it will become risks for human injury.

Cautions on use

                                                                                                                                                 

Cautions

 

Avoid installation locations that may be subjected to rapid changes in ambient temperature    

   or/and humidity.

 

Route the transmission cable separate from the inverter input/output power wiring.

      When disconnecting connection cable, make sure to hold its connector with care not to give    
      unreasonable stress to the cable and the unit.

 

Since connectors of optional cables have locking

      pawls for disconnection prevention at the inverter and the Option Unit, disconnect such a
      connector while pressing the pawl by finger for unlocking.

 

Mount the Option Unit securely on the panel, otherwise it could fall and cause malfunction or

   breakdown.

 

Connect an electromagnetic contactor or the like between the inverter and the power source to    

      secure external control of emergency stop of operation.

 

Do not assign the same inverter number to more than one inverter in the same system.

 

The inverter’s EEPROM has a life of 10,000 write cycles. Do not write to the same EEPROM      

      address more than 10,000 times.

Summary of Contents for RS4001Z-0











Reviews: