background image

   

E6580938

  

1

Safety precautions

On the inverter and in its instruction manual, important information is contained for preventing injuries
to users and damages to assets and for proper use of the device. Read the instruction manual
attached to the inverter along with this instruction manual for completely understanding the safety
precautions and adhere to the contents of these manuals.

Handling in general

 

Danger

Never

Disassemble

  Never disassemble, modify or repair the product.

      Disassembling the product could cause electric shocks, fire or injuries.
      For repairs, call your agency.

Prohibited

  Do not remove connectors when the power is on.

      It could lead to electric shocks.

  Do not put or insert foreign objects such as waste cable, bars, or wires into the product.

      It could lead to electric shocks or fire.

  Do not splash water over the product.

      It could lead to electric shocks or fire.

Mandatory

  Wiring should be conducted after turning the inverter power off.

  Turn off the power immediately in case any abnormalities such as smokes, smells or

abnormal noise are found.

      Neglect of these conditions could lead to fire.
      For repairs, call your agency.

Transportation and installation      

 

 

Danger

Prohibited

  Do not install or operate the inverter if it is damaged or any part is missing from it.

      Operating the inverter in a defective condition could lead to electric shocks or fire.

      For repairs, call your agency.

  Do not put any inflammable material near the product.

      It could catch fire if the product sparks because of a breakdown and the like.

  Do not install the product where it could be splashed with water and the like.

      It could lead to electric shocks or fire.

Mandatory

  The product must be used under environmental conditions prescribed in this instruction

manual.

      Using the product under conditions not specified by the instruction manual could lead to

breakdown.

 

Cautions

Prohibited

  Do not install the product in any place subject to vibrations or it could fall.    

      Otherwise it can cause injury to people.

Summary of Contents for RS4002Z-0















Reviews: