Station Apparatus
PC Attendant Console
Strata DK I&M 6/00
11-43
Station Apparatus
●
“AUX IN” can be used to send audio to the attendant and connected party. The audio level to
the attendant is approximately 10 dB below the audio level sent to the connected party. Audio
sent to the outside party is limited to–15 dBv (CO Tip/Ring). Use a 1/8” mini audio jack.
●
Chapter 10 – Universal Slot PCB Wiring
for RATI cable wiring
information.
PC Attendant Console Programming
Program 03: Code 51 assigns the RATU PCB attendant console cabinet slot number.
Important!
The RATU PCB takes up four station ports in software; each attendant console will
be assigned one of the ports in consecutive order. Toshiba recommends installing the
RATU PCB in the next highest slot number following the last station PCB installed–
do not skip slots. The first port number will be the next consecutive port number
following the last station port installed.
Program 15: If the attendant console is used to set-up trunk-to-trunk (two CO-line or tandem)
connections with loop start lines, set Program 15-5 appropriately; if the CO sends the AR-Hold
signal, set 15-0 and 15-3 to Detect. If the CO does not send the AR signal, set 15-0 and 15-3 to
Ignore. Loop start trunk-to-trunk calls remain on attendant hold loops only if AR-Ignore is set.
Program 58
♦
58-1: Sets the attendant console overflow time for each console.
♦
58-2: Sets the console display for EL or CRT (EGA) and enables or disables console call
waiting tone for each console. (Not used for the PC attendant console).
♦
58-4: Sets the console Answer key priority for each console.
♦
58-5: Sets the console overflow destination for each console.
Program 59: Assigns attendant console Flexible Buttons (Keys) for each console.
Attendant Console Load Share Programming
Program 81~89: Assigns CO lines (loop, ground, and DID) to share the incoming call load
between consoles. (Tie lines load share on Dial “0” calls only, without the use of Programs 81~89.)
All incoming CO lines (including DID lines) to be distributed between two or more Attendant
Consoles should be assigned to ring each console in Programs 81~89.
Note
Delay ring assignments do not apply to DID lines.
Program *09: Assigns the user company’s main listed [DN] (last four digits) to the attendant
console if DID lines should ring the console. If the DID lines are assigned to ring multiple
attendant console ports in Programs 81~89, DID calls will be distributed between the consoles.
Only one console (any one) should be assigned with the main listed [DN] in Program *09.
Programs 71 and 72: Can be used to provide an alternative assignment of DID calls using Program
*09. Program 71 assigns the dialed number to ring at different locations during each Night Mode
(Day, Day2, Night). DNIS tags can be added for personalized identification of calls. Program 72
provides external forwarding of calls listed in Program 71.
Program *17: Assigns each CO line to an attendant console as the DID line intercept position as
required. (Intercept calls do not load share.)
Summary of Contents for Strata AirLink DK40i
