Peripheral Installation
Voice Mail Options
12-44
Strata DK I&M 6/00
VM Groups
This feature groups VM QSTU2, KSTU2, RSTU2, RDSU/RSTS, PSTU or PESU ports together so
that message waiting set/cancel signals appear to originate from the lowest port in the VM group.
All VM ports connected to a particular VM machine should be set in the same VM group (Program
31, LEDs 05~08). The same ports set in the Program 31 VM group should also be set in the
designated VM Distributed Hunt Group in Program *40.
Message Waiting (MW) Set/Cancel
If the VM machine has the ability to dial a code and the appropriate station numbers to set or
cancel the message waiting LEDs on digital and electronic telephones, you can use Program 10-2,
LED 04 to instruct the VM machine to set or cancel a MW LED. See the
Strata DK Programming
Manual
for more information.
Note
Only dial codes
and
are set in the VM device configuration; the VM device dials
the station number automatically to set/cancel the MW LED.
No Conference VM
Prevents undesired three-party connections during VM call transfers. All VM ports should be set
for No Conference (Program 31, LED 09).
Privacy Override Deny
Prevents stations from overriding (breaking in) in-progress VM calls (Program 31, LED 18).
End-to-End Signaling
Enables VM port DTMF operation. All VM ports should be set for end-to-end signaling (Program
31, LED 17).
Note
The RRCS -4, -8, or -12 must be installed on the DK40i or DK424 RCTU to enable End-
to-End Signaling.
Receive Auto Call Forward ID Codes
Provides auto digits from call forwarded stations to direct callers to station mailboxes. All VM
ports should be set to receive auto ID code (Program 31, LED 16).
Voice Mail Program Checklist
Prior to Programming
Set Toshiba VP Maintenance Menu system parameters to “D” = Strata DK (any model). See
Toshiba Stratagy, Stratagy DK, or VP documentation for other parameter settings.
Programming Strata DK for Voice Mail
♦
Program 92: Initialization clears voice mail auto dial codes.
♦
Program 03: Verifies that a RRCS is installed on the RCTU, K4RCU3 or K5RC4 is installed
on the DK40i KSU, or the QRCU3 is installed in the DK14 to enable the VM device to send
DTMF tones. Also sets PIOU, PIOUS (code 43) or RSIU/RSIS (code 49) to enable the SMDI
port (see Program 76 if installing RSIU or RSIS SMDI port).
♦
Program 04: Assigns station Intercom or Directory numbers [DN] to VM ports (initialized
numbers recommended).
♦
Program 05: First digit of special codes
and
(initialized numbers recommended).
♦
Program *09: Sets DID extensions to ring VM Auto Attendant Ports if Program 71 is not used.
Summary of Contents for Strata AirLink DK40i
