background image

 

 

 

TPX Series UPS 700VA Operational Manual 

– 97673-000 

i

 

PRODUCT USE AND WARRANTY RESTRICTION

 

 

The Toshiba products listed in this document are intended for usage in general electronics 
applications  (computer,  personal  equipment,  office  equipment,  etc.).  These  Toshiba 
products  are  neither  intended  nor  warranted  for  usage  in  equipment  that  requires 
extraordinarily  high  quality  and/or  reliability  or  where  a  malfunction  or  failure  may  cause 
loss of human life or bodily injury (Unintended Usage). Unintended Usage includes atomic 
energy control instruments, airplane or spaceship instruments, transportation instruments, 
traffic signal instruments, combustion control instruments, life-support equipment, all types 
of safety devices, etc. Unintended Usage of Toshiba products listed in this document shall 
be made at the customer’s own risk. 
 

 

NOTICE 

 

PLEASE INFORM A TOSHIBA INTERNATIONAL CORPORATION 

REPRESENTATIVE IN CASE OF INCONSISTENCIES, OMISSIONS, OR QUESTIONS 

 

 
The  instructions  contained  in  this  manual  are  not  intended  to  cover  all  of  the  details  or 
variations  in  equipment,  or  to  provide  for  every  possible  contingency  concerning 
installation,  operation,  or  maintenance.  Should  further  information  be  required  or  if 
problems arise which are not covered sufficiently, contact the TIC customer support center.  

The  contents  of  this  instruction  manual  shall  not  become  a  part  of  or  modify  any  prior  or 
existing  agreement,  commitment,  or  relationship.  The  sales  contract  contains  the  entire 
obligation  of  Toshiba  International  Corporation's  UPS Division.  The  warranty  contained  in 
the contract between the parties is the sole warranty of Toshiba International Corporation's 
UPS Division and any statements contained herein do not create new warranties or modify 
the existing warranty. 
 
Any electrical or mechanical modifications to this equipment without prior written consent of 
Toshiba  UPS  will  void  all  warranties  and  may  void  the  UL/CUL  listing.  Unauthorized 
modifications can also result in personal injury, loss of life, or destruction of the equipment. 

 

 

QUALIFIED PERSONNEL ONLY 

 

Qualified  Personnel  are  those  who  have  the  skills  and  knowledge  relating  to  the 
construction,  installation,  operation,  and  maintenance  of  the  electrical  equipment  and 
have  received  safety  training  on  the  hazards  involved  (Refer  to  the  latest  edition  of 
NFPA 70E for additional safety requirements).

 

 

 

Summary of Contents for TPS0A0700AXA










































Reviews: