Reference Information
Toshiba
2-9
25
RECORDING
W
atching a TV pr
ogram while
recording another
1)
While recording, press
TV/VCR
to turn of
f
“VCR
” indicator
.
2)
Choose another channel using the channel
selector on the
TV
.
Skipping unnecessar
y scenes while
recording
Press
P
AUSE/STILL
to stop recording
momentarily
.
T
o
resume recording, press
P
AUSE/STILL
again.
Note
The VCR automatically shifts to the stop mode if the
recording pause mode continues for 10 minutes.
Basic Recording
1
Load a cassette with the safety tab attached.
2
Press
TV/VCR
so that the
“VCR
”
indicator appears in the VCR display
.
3
Select a channel to record with
CHANNEL
on the VCR, or
CH/TRK
or
number buttons
on the remote
control.
If you see
“L1/ L2
” ( For W
-522 only), or
“L
” ( For W
-422 only) in the
VCR display
, press
I.SELECT
so that the channel number appears.
•
If you record cable channels via the cable box, make the output
channel number of the cable box or
“L1
”( For W
-522 only ),
“L
”
(For W
-422 only ) appear
, depending on your connection. (See
pages 12
–
13.)
4
Press
SP/SLP
to select the
recording tape speed.
SP:
Suitable for general recording with
better picture and sound quality
.
SLP:
Suitable for tripling recording time, but with less picture and
sound quality than using the SP tape speed.
5
Press
REC
on the VCR, or
simultaneously press both
REC
on
the remote control.
Recording starts.
6
Press
ST
OP
to stop recording.
Recording off time setting
By setting the recording of
f time, the recording
stops and the VCR is turned of
f automatically
.
While recording, press simultaneously both
REC
on the remote repeatedly to set the desired off
time.
Each time you press
REC
, each half-hour up to
about 4 hours appear cyclically
.
Notes
•
To cancel the recording in progress, press
POWER
on the VCR
.
VCR
VCR
VCR
REC
TIMER
S
VCR
L
TIMER
VCR
RECORDING
Recording a TV Program
This section explains the basic recording operation.
Preparation
•
Select the video channel (3 or 4) or video input mode on the TV.
REC
TIMER
SLOW
PAUSE
/STILL
REC
TIMER
TV
VCR
POWER
I.SELECT
SP/
SLP
DISPLA
Y
TV VOL
COUNTER
PROG.
CANCEL
REMAIN/
RESET
COUNT
EJECT
CM SKIP
FF
REW
PLA
Y
ENTER
A.SELECT
1
2
3
6
5
4
10
0
9
8
7
0
ST
OP
5
I.SELEC
T
6
4
2
3
T
o
record from other
connected equipment
In step
3
, press
I.SELECT
to
switch the display as follows:
W-522
:
L1:
To record via the LINE IN
1 jacks on the rear panel.
L2:
To record via the LINE IN
2 jacks on the front panel.
W-422 :
L
: To record via the LINE IN
jacks on the rear panel.
24
1
On the SET UP screen, select
“COUNTER MEM.
” using
PLA
Y
or
ST
OP
, and set to
“ON
” using
REW
or
FF
.
2
Press
PROG.
to exit.
The memory-stop feature allows you to quickly return to a
counter reading of
“0H00M00S
” from any point on the tape.
Memory stop is automatically turned on whenever the time
counter with memory is displayed on the
TV screen.
This is
convenient when you want to watch a segment of the tape
repeatedly
.
Y
ou may also discover other useful application for
this feature.
Notes:
If you are rewinding the tape and the VCR stops at
“0H00M00S M
”, press
REW
again to continue
rewinding.
If you press the
FF
(fast-forward) button and the time
counter never reaches
“0H00M00S M
” between that
point and the end of the tape, the VCR will continue to
fastforward to the end of the tape.
Memor
y Stop Featur
e (Zer
o Retur
n)
SLOW
PAUSE
/STILL
REC
TIMER
TV
VCR
POWER
I.SELECT
SP/
SLP
DISPLA
Y
TV VOL
COUNTER
PROG.
CANCEL
REMAIN/
RESET
COUNT
EJECT
CM SKIP
1
2
3
6
5
4
10
0
9
8
7
0
FF
A.SELECT
ENTER
ST
OP
REW
PLA
Y
ENTER
FF
REW
STOP
REMAIN/
COUNTER
PROG.
COUNT RESET
PLAY
DISPLAY
E
n
D : PROG
TAPE LE
n
GTH
120 160 180
SAP SET
on off
COU
n
TER MEM
on off
LA
n
GUAGE E
n
G FRA ESP
For W-522 only
