Total TIRLI2002 Manual Download

Page: 11 / 17

Reversing switch lever

1. Reversing switch lever

This tool has a reverse switch to change the direction of rotation.

•

Press the reversing switch lever from side A to rotate clockwise.

•

Press from side B to rotate counterclockwise.

•

When the direction change switch lever is in the neutral position, the switch

trigger cannot be pulled.

Attention

Always check the direction of rotation before operation.
Use the reverse switch only after the tool has come to a complete stop. Changing the

direction of rotation before the tool stops can damage the tool.
When not using the tool, always place the reversing switch lever in the neutral position.

Mounting

Attention

Always make sure the tool is switched off and the battery cartridge is removed before

carrying out any work on the tool.

Installing or removing the driver bit/socket bit

(optional accessory)

Only use the screwdriver bit/socket bit shown in the figure. Do not use any other

screwdriver bit/socket bit.

Summary of Contents for TIRLI2002


















Search results

Summary of Contents for TIRLI2002

Reviews:

Related manuals for TIRLI2002

Brands by name

Popular brands

Total TIRLI2002, Manual

Search results

Summary of Contents for TIRLI2002

Reviews:

Related manuals for TIRLI2002

Brands by name

Popular brands