Totech U7002 Operation Instructions Manual Download

Page: 13 / 15

Repairs

Repairs should only be carried out by Totech service mechanics or relative-skilled personnel.

Failures

Faults

Cause of fault

Action

Humidity too high



Air mixture too low



Door open



Door contact not open



at least 1 Ventilator failure



Correction of air mixture



Check air filter, exchange if
necessary



Check door contact, exchange if
necessary



Ventilator exchange



Check electrical components

acc. circuit diagram

No report



Apparatus switched off



Mains switch in cold apparatus
element switched off



Main fuse gone



Use ON-key on display



Check electrical components acc.
circuit diagram

Fuses
Steering tension



Fuses gone



Exchange of fuses



Check electrical components
acc.circuit diagram

Report „Sensor failure“



Sensor gone



Exchange Sensor

Rotor drive



Drive motor gone



Exchange drive motor



Check electrical components
acc.circuit diagram

Summary of Contents for U7002
















Search results

Summary of Contents for U7002

Reviews:

Related manuals for U7002

Brands by name

Popular brands

Totech U7002, Operation Instructions Manual

Search results

Summary of Contents for U7002

Reviews:

Related manuals for U7002

Brands by name

Popular brands