background image

 

 

 

 

 

 

 

Obligation of personnel 

All  persons,  who  are  ordered  to  operate  the  air  dehumidifier,  should  commit  themselves,  before 
operation: 

  to observe the relative instructions regarding a safe operation and a prevention of accidents.  

  to observe the safety and warning instructions of this manual.  

Organizational Measures 

  The required personal protection equipment should be made available by the owner.  

  All present safety precautions should be tested regularly. 

Informal Safety Measures 

  The manual should always be kept on the place of operation of the air dehumidifier. 

  In addition to the manual the universally applied regulation and also the local regulation to prevent 

accidents and environmental protection should be observed. 

  All safety and warning instructions for the air dehumidifier should be kept in a readable way. 

Intended way of application 

The  air  dehumidifier  should  only  be  used  to  dehumidify  atmospheric  air.  Another  or  further  use  is 
considered not in accordance with the original purpose. For damage resulted from this Totech Europe 
Ltd will not be liable. 

Air dehumidifiers should not be put up in liquids or suck up liquids (f.i. full tanks or flooded 
surfaces etc.). 

The operation in and/or with explosion-sensitive atmosphere is permitted for RL 94/9/EG 
(Atex 95) marked apparatuses. The owner is obliged to check the ability of deployment of 
the air dehumidifier in accordance with the RL 1999/92/EG (Atex 137)! 

To use in accordance with its original purpose belong also: 

  the observing of all instructions in the manual and 

  the compliance of inspection and maintenance work.  

Dangers in operating the air dehumidifier 

The  air  dehumidifier  has  been  constructed  in  accordance  with  the  state  of  technology  and  the 
approved technical safety rules. The air dehumidifier should only be used: 

  for use in accordance with its original purpose 

  in technically safe conditions. 

  Failures, which can affect safety, should be repaired at once.  

Protection facilities 

  Before  any  switch  on  of  the  air  dehumidifier  all  protection  arrangements  should  be  applied 

adequately and be active. 

  Protection facilities should only be removed: 

a) after a halt and b) safeguarding against unintentional switching on.  

  On  supply  of  partial  components  the  protection  facilities  are  to  be  applied  in  accordance  with 

instructions.        

Summary of Contents for U7002
















Reviews: