background image

tousek

  /  E_PASS-838_02  /  22. 10. 2018 

- 5 -

100

800

100

100

FB

F

S

T

•  Lead the insulating sleeves 

(S)

 for power supply and acces-

sories into the opening of the base plate. 

•  Embed the base plate firmly and horizontally in the founda

-

tion 

(F)

 

(see  „examples - Barrier installations“ page 13).

•  Set the operator housing on the base plate with the door 

(T)

 aligned to the road 

(FB)

 and secure it with the bolts. 

Therefore it has to be ensured that the connecting cables 

won’t be damaged.

3.  Installation  

Barrier PASS 838

housing backside

3b.  Mounting the barrier boom 

Installation

 Important

•  The barrier boom can be installed either on the left 

or on the right side of the operator housing.

•  Please do not load additional weight (e.g. sign boards) 

on the barrier boom. This could result in the damage 

of the gearbox unit.

left barrier 

right barrier

FB

T

T

•  In a first step knock in a metall key 

(K)

 into the nut of the gearing drive shaft on the side of the barrier where you wish to 

mount the boom. 

•  The following  mounting steps differ in accordance of whether you wish to  mount the round or the flat barrier boom.

 

Important - 

grease the drive shaft

•  put some grease onto the external drive shaft with 

provided grease!

 

(see picture))

 Foundation

•  The foundations to be made must be at least 

100mm 

larger around then the foundation plates concerned.  

•  The foundation must be raised from the ground level to 

a minimum of 

100mm.

  

•  The foundation depth from ground level to should have 

a minimum of 800mm

 (frost resistant).

•  The foundation always has to be adjusted to the structure 

of the ground.

 

It should consist of concrete quality C20/25 at ground 

class 3. The foundation has to be horizontal and free 

of cracks.

•  When using a support fork/tip rest pay attention to the 

offset 

V,

 which depends on the barrier used (barrier 

boom):

 

For barriers with flat boom: 

V = 190

 

For barrier type PASS 838 L6  

(= barrier with round boom): 

V = 220

K

K

3a.  Mounting of base plate and barrier operator 

Installation

= barrier width - 25mm

290 180

180

255

290

100

100

base plate  

barrier operator

V

T

120

150

Ø30

FB

base plate 

guide in bracket

Summary of Contents for Pass 838

















Reviews: