background image

- 8 - 

tousek

  /  E_PASS-838_02  /  22. 10. 2018

SI

F

M

G

3e.  Force adjusment 

•  The force adjustment is made by the ST80 control board.
•  Due to the spring balance, the operator force is measured 

in a way, that the barrier boom may be stopped with little 

effort.

•  As an additional safety device we recommend the connection 

of a photocell.

3c.  Electrical connections 

Installation

•  Before carrying out the electrical connections, the power 

supply of the gate facility must be turned off !

•  Connect the operator to the control unit according corre-

sponding control manual  

 (mind the beside installation 

notes).

•  For the connection of  diverse safety devices, transmitters and 

other accessories please check the corresponding manuals  

(please note cable/wire plan).

 Warning

•  Before carrying out the electrical connections, the power supply of the gate facility must be turned off !  

•  The safety regulations for electric shock prevention have to be complied.

•  The device should only be connected by qualified personnel 
•  The device should not be used in an explosive environment !

•  An all-pole disconnecting mains switch with a contact opening gap of min. 3 mm has to be foreseen. 

The gate facility has to be secured according to the valid safety regulations!

• IMPORTANT: The control lines (buttons, radio, photocells, etc.) have to be laid separately 

from the 230V lines (supply line, motors, signal lamp). and may have a max. length of 50m.  

For length > 50m decoupling steps are necessary !

 

Important installation notes

•  Attention: The operator works with the condenser 

mounted on the motor. Therefore don´t connect an 

additional condenser to the control unit.

•  The operator housing is equipped with a safety switch 

(S) which stops the motor as soon as the housing 

lid is opened. This safety switch must be connected 

to the motor control unit (input for STOP switch).

3d.  Adjustment of spring tension 

Installation

•  The adjustment of spring tension is made by turning the 

screw nut 

(M)

 on the spring rod.

 Warning

•  The safety standards and regulations regarding the 

force adjustment have to be in compliance  with the 

effective rules !  

 Important 

•  The spring (F) has to be adjusted so that the boom 

can be moved easily by hand in emergency release 

state. (with pendulum arm and/or boom grid). 

The boom   should have a position of approx. 

20–40°.

Summary of Contents for Pass 838

















Reviews: