background image

13

PREFLIGHT

Identify Your Model

No matter if you fl y at an AMA sanctioned R/C club site or 
if you fl y somewhere on your own, you should always have 
your name, address, telephone number, AMA number and 
FAA number on or inside your model. It is required at all AMA 
R/C club fl ying sites and AMA sanctioned fl ying events and 
simply a “good idea” even if fl ying somewhere else. Fill out the 
identifi cation tag on page 15 and place it on or in your model.

Charge the Battery

Be certain to refer to the instructions that accompany the 
charger to properly and safely charge the battery that goes 
in the model and powers the motor and controls.

When discharging the battery, DO NOT attempt to fully 
discharge the battery pack by repeatedly running the motor 
to the ESC’s low voltage cutoff. This will drastically shorten 
the life of your Lithium polymer (LiPo) batteries and could 
cause the individual cells to become imbalanced.

MOTOR SAFETY PRECAUTIONS

   

WARNING:

 Once the motor batteries are connected 

the electric motor can start at any time. Make sure the 
fail safe is set on your radio to prevent the motor from 
starting if the signal is lost.

   

WARNING:

 Read the entire instruction sheet included 

with your motor batteries. Failure to follow the instructions 

could cause permanent damage to the battery and its 
surroundings and cause bodily harm!

   

WARNING:

 Get help from an experienced pilot when 

learning to operate electric motors.

   

ALWAYS

 keep these items away from the prop: loose 

clothing, shirt sleeves, ties, scarfs, long hair or loose 
objects such as pencils or screwdrivers that may fall 
out of shirt or jacket pockets into the prop.

   

ALWAYS

  keep  your  face  and  body  as  well  as  all 

spectators away from the plane of rotation of the 
propeller as you start and run the engine.

   

ALWAYS

 wear safety glasses when operating the motor.

   

ALWAYS

 remove the propeller if the motor batteries will 

be connected when working on your plane.

   

ALWAYS

 remove the motor batteries when charging.

   

ALWAYS

 follow the charging instructions included with 

your charger for charging LiPo batteries. LiPo batteries 

can cause serious damage if misused.

   

ALWAYS

 unplug the motor batteries fi rst.

   

ALWAYS

 use a LiPo approved charger.

   

ALWAYS

 set the charger’s output volts to match the 

battery volts.

   

ALWAYS

 charge a LiPo battery in a fi reproof location.

   

ALWAYS

 charge through the “charge” lead.

   

ALWAYS

 KEEP OUT OF THE REACH OF CHILDREN.

   

ALWAYS

 remove the batteries from the plane after a 

crash. Set them aside in a safe location for at least 20 
minutes. If the batteries are damaged in the crash they 
could catch fi re. If the battery starts to swell, quickly 
move the battery to a safe location, preferably outside. 
Place it in a bucket, covering the battery with sand. 
Never use water to try and put out a LiPo fi re.

   

NEVER

 operate the motor in an area of loose gravel 

or sand; the propeller may throw such material in your 
face or eyes.

   

NEVER

 touch the motor during or right after operation. 

The motor gets HOT!

   

NEVER

 switch off the transmitter with the motor 

batteries plugged in.

   

NEVER

 use a NiCd/NiMH peak charger to charge a 

LiPo battery.

   

NEVER

 charge in excess of 4.20v per cell unless the 

battery is rated for a higher voltage.

   

NEVER

 charge through the “discharge” lead.

   

NEVER

 charge at currents greater than 1C unless the 

battery is rated for a higher charge rate.

   

NEVER

 trickle charge a LiPo battery.

   

NEVER

 allow the battery temperature to exceed 150 

degrees F (65° C).

   

NEVER

 disassemble or modify the pack wiring in any 

way or puncture the cells.

   

NEVER

 discharge below 2.7V per cell.

   

NEVER

 place the battery or charger on combustible 

materials  or  leave  it  unattended  during  charge  or 
discharge.

   

NEVER

 charge the batteries in the plane.

FLYING THE P-51 MUSTANG

While the P-51 is fairly easy to fl y, it is not a trainer. If you have 

never fl own a model aircraft before, it is strongly suggested 
that you learn to fl y with the assistance of an experienced 
R/C pilot.

Find a Suitable Flying Site

Find a fl ying site clear of buildings, trees, power lines and other 
obstructions. Until you know how much area will be required 
and have mastered fl ying your P-51, a site at least the size 
of two or three football fi elds should be adequate—a fl ying 
fi eld  specifi cally intended for R/C planes is best. Don’t fl y 
within six miles of R/C fl ying fi elds and never fl y near people.

Summary of Contents for P-51 MUSTANG MKII EP Rx-R

















Reviews: