Tower Hobbies Tower Trainer 40 ARF Instruction Manual Download | Manualshive

Page: 9 / 30

background image

❍

5. Test fit 1/8" plywood Former F2 in place on the Right Fuse

Side. Press it down into its slot and use a 90 degree triangle to
keep it perpendicular to the fuse side. Glue it in place with
Medium CA.

❍

6. Test fit the die-cut 1/8" plywood Former F3 in place on the

Right Fuse Side. Press it down into its slot and use a 90 degree
triangle to keep it perpendicular to the fuse side. Glue it in place
with Medium CA.

❍

7. Position the Left Fuselage Side onto the formers. Use

Medium CA and glue the fuse side to the formers.

❍

8. Test fit the die-cut 1/8" plywood Landing Gear Plate (LGP).

Once satisfied with the fit, glue it with 6-minute epoxy.

❍

9. Cut the remaining 1/4" x 1/4" x 36" balsa stick into two 12"

pieces to be used as the Servo Rails. Position the Servo Rails so
they are flush with the aft edge of the main fuse side. They will
extend forward of Former F2 when installed. Wick Thin CA along
the edges of the rails and fuse sides to glue them in place.

17

❍

10. Cut the "Fuselage Top View" section from the fuselage plan

sheet and tape it on your building board. Tape a piece of wax
paper or Plan Protector over the plan.

❍

11. Locate the die-cut 1/8" plywood Forward Fuse Bottom.

Tape the Forward Fuse Bottom onto the fuselage. Set the fuselage
assembly upright (in its normal position) on the waxed paper.
With everything in its proper place, apply thin CA glue to all the
joints, around the formers and along the bottom. Keep checking
the parts fit and alignment as you glue. Wait a minute for the glue
to set, then apply thick CA to the joints to make sure a good bond
exists, especially in the joints that do not fit perfectly.

Note: The use of CA accelerator will be helpful when using thick
CA to fill any large gaps.

❍

12. Locate the die-cut 1/8" balsa Aft Fuse Bottom and pin it

over the top view. Carefully align the fuselage sides and glue the
LGP to the front of the die-cut 1/8" balsa Fuse Bottom with
Medium CA. Use weights and/or pins to hold the fuse sides in
position. Place one die-cut 1/8" plywood Former F4 and one
die-cut 1/8" plywood Former F5 in their respective positions
against the Aft Fuse Bottom.

❍

13. Pull the fuse sides against Former F5. The fuselage sides

should be centered on the bottom sheet. Press the Fuselage Sides
down tightly against the sheet and snug against the former. Press
Former F5 tightly against the Stabilizer Base. Use Medium CA to
glue the Fuse Sides to the Fuse Bottom and Former F5.

❍

14. Pull the fuse sides against Former F4. The fuselage sides

should be centered on the bottom sheet. Press the Fuselage Sides
down tightly against the sheet and snug against the former. Press
Former F4 tightly against the Balsa Center Support. Use Medium
CA to glue the Fuse Sides to the Fuse Bottom and Former F4.

18

«
...
7
8
9
10
11
...
»

Summary of Contents for Tower Trainer 40 ARF































Reviews:

No comments

Related manuals for Tower Trainer 40 ARF

Brand: Faller Pages: 24

Brand: Jet Hangar Pages: 2

P-47 Thunderbolt

Brand: J. Perkins Pages: 16

Brand: J-Power Pages: 32

Brand: N-Tech Jets Pages: 10

Brand: LaTrax Pages: 11

Pilatus PC-6 Porter

Brand: Kavan Pages: 20

Little white rocker

Brand: Bandits and Angels Pages: 5

Brand: PLAYTIVE JUNIOR Pages: 20

Paradise AquaCraft

Brand: Hobbico Pages: 12

Habu 32 EDF ARF

Brand: E-FLITE Pages: 108

Brand: Old School Model Works Pages: 22

Brand: Joustra Pages: 16

Albatross D III

Brand: REVELL Pages: 6

Brand: STAX Pages: 19

Brand: REPTILE Pages: 2

Brand: E-FLITE Pages: 20

Brand: Air Hogs Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands